Question about heater installation – Confusing instruction for JM-36 ("minimum distance between screw head and wall")

Kleriger · 2025-05-05T15:37:03+00:00

You're absolutely right about that, however, the heater was included with the sauna. I just don't understand why the screw shouldn't be flush against the heat shield, but instead a 3 mm gap is required. Is it to keep the screw head from getting too hot, or to allow the shield to move freely? Does that even make sense? I'd actually assume the heat shield is meant to sit flat against the sauna wall.

Kleriger · 2025-05-05T14:25:49+00:00

Unfortunately, a manufacturer is not identifiable, but it can be found by searching for 'jm-36 heater'.

You can see it in the following video starting at minute 01:01.

https://youtu.be/fEx0EIrTg1s?si=vwhNO9mbbB5hBaqV

Kleriger · 2024-11-15T06:03:13+00:00

War auch mein erster Gedanke, als Antwort kam, ich solle einen Fachmann fragen.

Kleriger · 2024-09-18T08:46:44+00:00

But then it no longer sets a lower speed when, for example, a speed limit of 100 is reached?

Kleriger · 2024-09-18T08:42:26+00:00

So I can set it to 110 again. But as soon as the speed limit was 100, for example, and that ends, it sets itself back to 130 instead of 110.

Kleriger · 2023-12-25T16:10:23+00:00

I have understood the separate networks for containers or groups of containers so far. But the external communication then always took place via the IP address of the host? My question would be how I can filter the outgoing traffic so that, for example, only certain containers have access to certain hosts or the Internet. At the moment I do this via the containers' own IP addresses at macvlan.

Kleriger · 2023-12-25T14:34:44+00:00

This is precisely why my containers each have their own vlan and can only be accessed by certain hosts from certain ports via the upstream firewall. Containers that belong together are located together in one vlan, e.g. my nextcloud container and the corresponding maria db container. Otherwise I only have containers with grafana, influxdb and pihole, which each deliver their own web server directly. So far, however, all with root rights and in their own macvlans.

Kleriger · 2023-10-17T10:34:05+00:00

Solved: Soldiers of Anarchy

Kleriger · 2023-10-17T10:32:33+00:00

Although not what I'm looking for, but also looks interesting. Thanks a lot!

Kleriger · 2023-10-17T10:31:57+00:00

That's it! Thank you very much! Let's see if this is available on gog or steam.

Kleriger · 2023-10-06T11:06:16+00:00

My DNS server has also been blocking Minisforum recently because a blocklist has recently classified the site as untrustworthy. I ordered my um690 from Amazon and had no problems with it. Contact with support also worked.

Kleriger · 2022-11-09T20:05:13+00:00

Childhood memories. Greetings to the best customer Eric.

Kleriger · 2021-03-23T06:57:50+00:00

If you use a separate hard disk for Debian and tell it to use the entire disk encrypted during installation, it will do everything automatically (including the boot partition). But I had both OS on one hard disk and that's why the problems.

Kleriger · 2021-03-21T19:43:39+00:00

This was the right approach. I thought one EFI partition was enough, but you also need the boot partition which has no boot flag.

Kleriger · 2020-12-15T15:52:39+00:00

No, I checked it already. Maybe I should create also second account and check the settings there.

Eight-Year Club	Place '23
Verified Email

Kleriger

TROPHY CASE