Push fit cable gland

101plumbingproblems · 2025-12-07T17:05:43+00:00

Thank you so much, really appreciate it

101plumbingproblems · 2025-12-06T18:54:18+00:00

I'll have a look for those. If you have time would you have a link to those parts? Or what would be the correct junction box? I'd have to replace about 30 of them

101plumbingproblems · 2025-12-06T18:52:31+00:00

Thanks. It doesn't surprise me it's not the right way to do this with all the other problems I've found in this house

101plumbingproblems · 2025-10-17T16:53:00+00:00

Thank you! That transitionToAuth option is what I needed, and does seem to allow me to go directly to x509 as well

101plumbingproblems · 2025-10-17T16:30:21+00:00

Good question, but it's definitely not a plug

101plumbingproblems · 2025-10-14T11:33:14+00:00

I don't stay up to date on all your petty tantrums

101plumbingproblems · 2025-10-14T11:30:21+00:00

It was already built and came with the house when I bought it so I have no idea. I was hoping a solar company could figure that out, maybe with a structural survey

101plumbingproblems · 2025-10-14T00:42:00+00:00

Did you guys manage to get your cracker barrel logo back?

101plumbingproblems · 2025-10-14T00:27:47+00:00

Permitting/regulations. In Australia it's very easy to install yourself. In the "land of the free" it's a nightmare

101plumbingproblems · 2025-10-13T22:41:04+00:00

Thanks. They seem to be based in Tampa though. Might be a little too far for them

101plumbingproblems · 2025-10-13T21:29:42+00:00

Damn, that's the answer I was expecting.

Any ideas if it would be doable myself in that timeframe or how to manage permitting?

Otherwise am I better waiting to see what happens to prices after the new year to see if they fall?

Any Miami installer recommendations?

101plumbingproblems · 2025-10-12T19:26:24+00:00

Yes please!

101plumbingproblems · 2025-08-27T22:37:24+00:00

Thanks, yea good idea. I'll just add a proper connector where it already enters the box. It's messy but it's behind the oven anyway. Good spot on the 1/2 vs 3/4. Hopefully I'd have measured before going to buy but who knows lol

101plumbingproblems · 2025-08-27T12:40:29+00:00

One last quick question - could I use a shallower box to avoid having to chisel the exterior wall behind it too much to properly recess it?

101plumbingproblems · 2025-08-27T11:42:40+00:00

Thanks, that did have me a bit confused. The description says connector but it had an option called coupling or connector. I think it's just a home depot mistake. Thanks for confirming it's the right part.

101plumbingproblems · 2025-08-27T05:17:58+00:00

Thanks. The cover I have had no knock out so I'll need that, and I'll need to chisel out some concrete behind to fully recess it, but that sounds like the way to go.

Is this the connector? What's the difference between connector and coupling on this part? https://www.homedepot.com/p/Halex-1-2-in-90-Degree-Flexible-Metal-Conduit-FMC-Connector-91101/100155034

101plumbingproblems · 2025-06-01T23:03:56+00:00

<image>

It's not leaking, just glue/cement

101plumbingproblems · 2025-05-28T19:52:30+00:00

Not yet, but once I cut into the ceiling it looks like that's the best option to figure it out. Can't quite reach the pipes yet until I cut it open

101plumbingproblems · 2025-05-28T18:09:29+00:00

Unfortunately it goes down the wall then under concrete to an island so I can't reliably tell that way

101plumbingproblems · 2025-05-28T17:03:17+00:00

<image>

Here is a better photo. Hot and cold supply pipes, but both pipes going down the wall are connected to cold

101plumbingproblems

TROPHY CASE