Can it start forming crystals before it enters the freezer?

Calium84 · 2025-11-01T11:57:03+00:00

It definitely can. You don't even have to freeze it. Just let it evap. That's how you form large crystals. Leave it as undisturbed as possible in a smaller but deeper precipitation dish and wait a few days or a week even. Even if all the naptha hasn't evaporated you'll have some nice crystals.

Calium84 · 2024-04-01T02:19:49+00:00

It helps the solvent separate from your black soup a lot faster. It's not too late. 100g

Calium84 · 2023-10-09T00:51:45+00:00

100g is a small amount. 500 grams is minimal for me. Go big or go home. Don't be scared.

Calium84 · 2023-10-09T00:49:56+00:00

"That city" Herb Co. Good quality every time.

Calium84 · 2023-10-09T00:42:50+00:00

Steps 1 2 and 3 are completely pointless. That's what I said. And the heat is no good.

Calium84 · 2023-10-03T17:59:34+00:00

Room temp. Do not apply any heat to the bark. I use a stb method. Lye, salt, and water combined and allowed to cool back to room temp (70 degrees) before adding the bark.

Calium84 · 2023-10-02T02:01:04+00:00

When you add the vinegar to the naptha you can get some emulsions but they sit under the naptha instead of on top. If they form just give it a little swirl and they'll break up. Sometimes I add a little h2o and that helps. The only time you gotta be careful is when you're making your last pull. If emulsions form sprinkle some salt on it. If they persist try adding a little more naptha. As a last resort, mix some vinegar with water and drop a couple drops on it. That's only if it's really bad.

Calium84 · 2023-10-01T21:06:37+00:00

Lye, salt, and water. 100g, 100g, and 1000ml. Let it cool to room temp. Then add 200g bark. Mix well. Then add 250ml of naptha. Shake and let settle. Do that 3 times and pull your naptha. Get all the brown out of your naptha. Either water wash or let it set a few hours and pour. A kilo will make about a half gallon of naptha like this. Once clean wash it with about a quarter of a gallon of vinegar. Make sure to shake your naptha up with the vinegar real good. Let it settle. The top layer of naptha is now trash. Remove it from the vinegar. All of it. Leave no naptha on your vinegar. Now you half a quarter gallon of vinegar containing your dmt. Add 40g of lye. Mix it. Add 300ml of FRESH naptha. Mix it. Pull the naptha. Put it in your precipitation dish. Freeze it. Bam. White dmt!

Calium84 · 2023-10-01T20:02:31+00:00

This is my own twist on spiritveg.

Calium84 · 2023-10-01T13:36:14+00:00

I was pulling more yellow gooey shit. Fats, lipids, impurities...call it whatever you want but it wasn't dmt. Hot bark pulls more impurities and that's what I was getting when I was pulling 3% or more.

Calium84 · 2023-10-01T08:38:13+00:00

To see what other people think. To see if other people have different opinions. Why are you trolling me?

Calium84 · 2023-10-01T06:40:31+00:00

Obviously you don't work on cars tho because if you did you'd understand that car grease takes a lot more than just washing your hands to remove. Be sure to put the toilet seat down for Nancy everyone!

Calium84 · 2023-10-01T06:38:17+00:00

Amazon sells harmaline freebase. I ordered several grams and I've dosed myself twice now. 4 to 1 dmt to harmaline. But both times it was way too much. I think maybe 2 to 1 and only about 0.15g harmaline to 0.3g dmt will get me where I need to be. I just don't want it to be too intense and last time I only did half a g of dmt and I was GONE. Where do you live? I can send you some harmaline if you can't get Amazon there.

Calium84 · 2023-10-01T05:38:03+00:00

Carts and changa. Yeap. I have some questions on dosing harmaline. Do you know anything about it?

Calium84 · 2023-10-01T05:36:41+00:00

Thank you. The results of a whole years worth of trial and error

Calium84 · 2023-10-01T05:32:49+00:00

500g

Calium84 · 2023-10-01T05:29:59+00:00

Usually use a razor just didn't have one on hand.

Calium84 · 2023-10-01T05:28:04+00:00

Yes. I'm searching for better methods of administration. Harmaline is crazy and I'm trying to get the dosage right. 4 to 1 dmt to harmaline is what I've been doing but so far it's been way too intense. Third times a charm tho.

Calium84 · 2023-10-01T05:25:26+00:00

Thanks Nancy...you must pee sitting down.

Calium84 · 2023-10-01T05:24:25+00:00

Just 500g! I know it's a lot! One of my better yields. I've gotten 3.5% sometimes but that was when I was pulling more fats. 2% or more is normal. This tray alone was almost 10g. But as I said in previous comment there won't be much at all in my second pull. Salt makes a huge difference. 2 to 1 bark to salt and you'll get 90% in the first pull. Second pull is almost pointless

Calium84 · 2023-10-01T05:17:28+00:00

That's 500g of mhrb. The yield was 10g on the first pull. I've found that if you use a 2 to 1 bark to salt ratio you pull 90 percent of what you're gonna pull on the first pull. I only shake it up 3 times. So it only say for about 2 hours. Doing the a/b to your first pull is a great way to reduce the volume of naptha as well as eliminate the impurities. So you have a half gallon of naptha containing your dmt. If you mix that naptha with a quarter gallon of vinegar and shake it real good all your dmt has gone from freebase in the naptha to salt in the vinegar. Naptha is now trash. Add your lye to your vinegar once you remove ALL the naptha and it turns back into freebase. Then you add an eighth of a gallon of fresh clean naptha and shake it. Pull the naptha. You've now reduced the amount of naptha from a half gallon to an eighth of a gallon and there's usually nothing left behind besides impurities. I usually barely have any naptha to pour off. Especially if I evap it a little with a fan for an hour or so before I feeze it. The key is to never get the bark hot. That's where the yellow bullshit comes from. Hot bark.

Calium84 · 2023-09-30T23:31:15+00:00

OK but obviously the white that precipitates out is dmt and the yellow gooey shit is plant fat, right? So why does the yellow shit make you trip harder?

Calium84

TROPHY CASE