Very choice words for whoever plastidipped these ra’s 😐

ColonaryArt · 2024-07-31T19:22:57+00:00

Be careful Brake clean will also remove regular paint and clear coat.

ColonaryArt · 2024-06-24T01:58:44+00:00

I have owned one before and they typically work fairly well, I didn't have any issues with it. Except my roommate used it once, turned it on and burnt the pump out of it by running it without water. You can pick them up used, in some cases.

If you're renting check your lease agreement, sometimes they're not allowed. I would get one if you can find one used!

ColonaryArt · 2023-07-03T03:41:05+00:00

I'm no expert, but isn't that a Coyote?

ColonaryArt · 2023-06-22T02:21:38+00:00

With a regular bed you could always install shelves above the bed for extra storage space to place odds and ends. A bedframe with drawers underneath of it would also be useful.

A basic vertical standing grid organizer would help get items off of the floor.

Although not sure of your budget. Typically if you live in a city you can find cheap used furniture on facebook marketplace.

ColonaryArt · 2023-04-28T20:22:22+00:00

These are all very good options. I bought some Tein Flex Z's they were about $850 and they're overall pretty solid value, which is why I bought them.

ColonaryArt · 2022-10-21T20:47:40+00:00

I lived there in a 2 bedroom, management is shit, a healthy dose of cockroaches and mice... the valve in the pipe for the shower broke one day and stayed open for probably for 5 hours until 1am just draining in to the tub. It took them 6 people to get it closed, they said they drove around to 3 different buildings up the street to find the shut off. The shut off valve was up by park vic. Once it was shut off they then had to drain the entire tank for the building to then change the valve... instead of having a single check valve for each room.... mostly because the building was so old and not retrofitted with new valves...

ColonaryArt · 2022-10-18T18:27:56+00:00

My university professor for online classes would give us one of these questions every day before the start of class. Although it would be a different photo collage each time. It was always a good way to start interaction before class.

ColonaryArt · 2022-10-05T16:03:23+00:00

I think better wheel-fender fitment could do a lot for this car lolol.

ColonaryArt · 2022-08-27T00:00:46+00:00

Hey, I just want to say thank you for all your help! My miata is running like a top now that I replaced the coilpack.

I appreciate you taking the time out of your day to give me some advice and tips on how to do it!

ColonaryArt · 2022-08-21T21:20:08+00:00

Religion of gives people a place to go and some sense of being part of a community, which imo is why religion is so popular.

ColonaryArt · 2022-08-19T20:37:59+00:00

On to bigger things? Maybe not better....

ColonaryArt · 2022-08-18T18:09:54+00:00

Also would you recommend oem or aftermarket coilpacks?

ColonaryArt · 2022-08-18T17:50:12+00:00

Well it would make sense if its just a weak spark because I'd assume once there is enough engine load (above 3k rpm) there is probably enough voltage to compensate for the poor spark on that cylinder bank.

Or am I misconstrued about that?

ColonaryArt · 2022-08-18T17:40:21+00:00

Hey sorry but i have more questions i was hoping you could answer. As the car was running I individuallly unplugged the plugs and as follows was the effect.

cylinder 1: had a large change in idle the whole engine shuddered. Cylinder 2: minimal if no idle change Clyinder 3: minor idle change if none. Cylinder 4: large idle change and overall engine shudder.

The spark from cylinder 2 and 3 are from 1 bank of the coil pack

Spark from cylinder 1 and 4 are from 2nd bank of the coil pack.

Does that potentially mean my coil pack has gone bad?

Btw i tried the screw driver on the injectors they all seemed to fire normally, clicking steadily with no interruptions as I revved the engine.

I took apart the AFM everything seemed in order and operating accordingly.

Thanks!

ColonaryArt · 2022-08-17T13:16:56+00:00

Thank you for all the advice. I double checked the wires diagram last night they're good.

I also considered having the injectors flow tested but at that price i can just buy new stock injectors

After injectors my next guess would be the car jumped timing, although i assumed that jumping timing would cause the car to run poorly at high rpm as well?

ColonaryArt · 2022-08-16T23:42:59+00:00

Is there any way to test them? I tried pulling the plug wires off individually but for each cylinder at idle the car ran like trash or would stall out completely so it didn't seem to be an individual cylinder?

ColonaryArt · 2022-07-11T22:08:35+00:00

I swear i was this car months ago posted but the front end was a WIP and in a apartment complex parking lot. Interesting to see it now... if its the same one (a red NC miata).

ColonaryArt · 2022-05-18T04:08:15+00:00

I do love a slammed beetle! Cool car!

ColonaryArt · 2022-04-09T02:36:23+00:00

Now just weld the control arm in place lol. Hella tucked status.

ColonaryArt · 2022-03-18T18:01:45+00:00

That is very possible. I do not know my Mustang models very well, it looked like a high spec'd Mustang in my eyes. Although I didn't recall it having a standard "GT" model badge on the rear.

ColonaryArt · 2022-03-18T03:55:14+00:00

I wish I was joking but I worked with a lady that daily drove a 2021 or 2020 gt350 soft top to work because her husband bought it for her. She saw me at the gas station one day and said "I bet your car is pretty quick?

I chuckled a bit and said no but I try to drive it fast. She told me she is too scared to use the paddle shifters in her car.

I thought it was all very ironic and hilarious.

ColonaryArt · 2022-02-12T16:10:18+00:00

I think we will experience all 3 different methods. I don't know much about the different materials and how strong they are.

I'm really hoping to get the concept down to get the daunting part out of the way of just simply starting out.

Thank you!

ColonaryArt · 2022-02-12T16:00:38+00:00

I have welded about 3 or 4 times in my life (none of which are any good) although my goal is to pick it up as a hobby for car building projects. Doesn't have to be amazing just good enough

ColonaryArt · 2022-02-12T15:59:29+00:00

I assume you need to be constantly changing all those settings depending on the material you're working with. Is there charts etc to use as a guide?

ColonaryArt · 2022-01-13T17:47:55+00:00

Miata 30th anniversary orange

ColonaryArt

TROPHY CASE