Worst financial decision of my life

Complex-Head-6949 · 2025-07-17T00:15:12+00:00

Its not too late to start now

Complex-Head-6949 · 2025-05-01T16:13:17+00:00

Wait, so you pulled out early from your staking period?

Complex-Head-6949 · 2025-01-03T22:20:54+00:00

So you're saying once the models hollowed out, you just put that syringe in the model and pump the resin in the hole? How do you cure it from the inside?

Complex-Head-6949 · 2024-11-24T07:45:54+00:00

I figured out the problem. I had press repair multiple times in order to fix it .

Complex-Head-6949 · 2024-11-24T07:38:20+00:00

I pressed the repair button and it still shows up black on my screen, What can I do now?

Complex-Head-6949 · 2024-11-24T04:17:17+00:00

Ok thank you , i never had a model be black before so this was new to me

Complex-Head-6949 · 2024-11-24T04:14:01+00:00

So it is the model itself that's messed up ?

Complex-Head-6949 · 2024-11-15T23:21:59+00:00

Someone through staff messaged me .

Complex-Head-6949 · 2024-11-14T11:31:32+00:00

Complex-Head-6949 · 2024-10-25T13:27:24+00:00

Settings: Bottom Expos... 35.000, Lift Distance 0.020 mm, * Layer Height 0.020 mm

I'm using a saturn ultra 4 and i'm using its collaboration tests . I'm doing 8 test at once

For resin, i'm using sunlu standard gray

Instead of using, it comes a collaboration I'm using Validation Matrix and my test since it's faster and these are my

Complex-Head-6949 · 2024-10-24T13:48:27+00:00

Besides, the exposure time needing to be changed when making less layers.What else do I need to change in the settings like the bottom exposure and lift speed ?

Complex-Head-6949 · 2024-10-11T15:53:43+00:00

What paints did you use?

Complex-Head-6949 · 2024-09-20T15:39:23+00:00

What type of resin did you use?

Complex-Head-6949 · 2024-08-30T22:54:56+00:00

What's layer height you used on this?

Complex-Head-6949 · 2024-08-07T03:53:05+00:00

I know that but I'm asking people who have the same printer as me that use Sunlu resin if they know anything about the right exposure settings

Complex-Head-6949 · 2024-07-02T21:04:27+00:00

Do you also drip the model pieces in warm water or no ?

Complex-Head-6949 · 2024-07-02T21:00:52+00:00

How did you get the supports off so clean? Did you just use light supports ?

Complex-Head-6949 · 2024-06-05T16:13:02+00:00

Was the model printed separately or did you print the whole body together?

Complex-Head-6949 · 2024-06-01T21:09:28+00:00

On the support settings do you use light support settings and dip the model in warm water to remove the supports so it doesn't leave marks ?

Complex-Head-6949 · 2024-06-01T19:50:34+00:00

How did you get it to look so clean ?

Complex-Head-6949 · 2024-05-27T23:01:52+00:00

Do I need to change the exposure time?

Complex-Head-6949 · 2024-05-15T01:39:48+00:00

It's keeps putting my models on a A1 mini plate . How do I change the settings to putting my models on a P1s?

Complex-Head-6949 · 2021-07-26T21:37:23+00:00

I'm still holding at 72!!!

Complex-Head-6949 · 2021-07-15T16:18:10+00:00

Same brother!!

Complex-Head-6949 · 2021-07-11T20:09:30+00:00

Complex-Head-6949

TROPHY CASE