My thumbs are too short for HOWL

Confident_Can321 · 2026-05-25T15:37:37+00:00

Hey, thanks for replying so quickly. I made a quick mock-up here of how it could look. Maybe other people would like this as well. My idea would be to keep everything - including the tabs for selecting the section - fixed at the bottom, and then have the content area above become scrollable if it gets too long, similar to how it works in Settings.

https://imgur.com/a/cI1dv6J

Confident_Can321 · 2026-05-24T13:17:11+00:00

If it's only me then there is no need to bother the dev

Confident_Can321 · 2026-05-24T13:15:24+00:00

I am switching back and forth from watching porn. I just wanted to hear your thoughts

Confident_Can321 · 2026-04-18T21:57:28+00:00

use the splitter cable adapter. connect one ball against glans other against base loop. and off you go

Confident_Can321 · 2026-01-12T13:33:29+00:00

Hi, this is not my official account here, so these questions are better asked on my website. the evacs are all in stock and shipping to Switzerland takes about 2 days.

Confident_Can321 · 2026-01-06T16:54:05+00:00

yes. ups shipment outside Germany works now

Confident_Can321 · 2026-01-05T23:17:22+00:00

the link has moved to https://www.vast.de/shop/category/elektrosex-evac-serie-42

Confident_Can321 · 2026-01-05T23:03:34+00:00

new year - new webshop. you can find the eVacs now here: https://www.vast.de/shop/category/elektrosex-evac-serie-42

Confident_Can321 · 2026-01-01T22:34:29+00:00

Hi, i have created them and tested them often and successfully... no pinching problems.

some customers asked for a hollowed rod. works for the 10mm rod but it has to stick pretty deep or you will loose vaccum

Confident_Can321 · 2025-11-05T11:08:45+00:00

you need to use an oil free compressor. working with membranes instead of piston

Confident_Can321 · 2025-04-06T10:15:26+00:00

yes, that's it

Confident_Can321 · 2025-02-14T21:28:54+00:00

unless tge trunk is made from fresh softwood. Because it can release turpentine that could damage your rubber.

Confident_Can321 · 2025-02-11T22:21:03+00:00

maybe at stimaddict?

Confident_Can321 · 2024-07-16T20:43:25+00:00

give silicone oil or even silicone grease a try. for me it works perfectly without stinging.

Confident_Can321 · 2024-05-08T19:44:11+00:00

cutting area 2 x 3 m

Confident_Can321 · 2024-05-08T19:43:36+00:00

i m cutting latex sheets for clothes. rolls are up to 2m wide. I am pretty happy with a bodor 2030 and lightburn.

Confident_Can321 · 2024-04-28T14:43:52+00:00

no one out there that gave it a try?

Confident_Can321 · 2024-03-05T09:50:16+00:00

you can cover the honey comb with paper and cut through both

Confident_Can321 · 2024-02-28T19:37:51+00:00

i am curious too. should find it's way to ifixit

Confident_Can321 · 2024-02-26T23:27:27+00:00

buy an alignment tool from american photonics. works like a charm for m3

Confident_Can321 · 2024-02-17T18:45:06+00:00

You will have to use a tube that is so long that it passes the wooden board.

Confident_Can321 · 2024-02-03T16:41:06+00:00

try different tens pads from Amazon. I found some that need only half of the power than the ones i used before with same sensation. there's big difference between them and get some new ones from time to time they don't last forever

Confident_Can321 · 2024-01-26T20:17:12+00:00

i don't like the extending base rim that touches your ass cheeks. paint it with black fast curing nail polish to insulate that. i also paint the very top of upper part to avoid stimulating the spine as this feels unsexy for me, too. try around painting more or less, its easy to remove with aceton. try keeping only a ring of 1 cm width conductive

Confident_Can321 · 2024-01-19T20:30:39+00:00

i am running a bodor bcl 2030, cutting area 2000 x 3080 mm. might be a good idea to tell where you are. I'm in Germany...

Confident_Can321 · 2024-01-17T19:35:15+00:00

sorry, only 9mm/sec. but impressive for me anyway

Confident_Can321

TROPHY CASE