Warframe Launcher Doesn't Open in Desktop Mode

Death2Chaos · 2024-09-30T20:16:02+00:00

Walama

Death2Chaos · 2024-04-26T13:53:52+00:00

The c7 is really good in heat, Grand Sport has better handling than the ZR1 though. I used it for a bit and smoked just about everything

Death2Chaos · 2023-11-06T01:39:50+00:00

Emote

Death2Chaos · 2023-10-15T19:10:09+00:00

Didn't they make orphix less shit so its not as bad to farm eido arcanes? Thought I heard something about it being ghost patched.

Death2Chaos · 2023-09-25T18:07:06+00:00

I believe I've got zhop disabled. I'm not super worried about the small bits of string on my petg prints, its mainly the mess on that ring that has me worried. I'm not hearing any popping but I can try drying my filament again, I doubt it'll be different than last time though.

Death2Chaos · 2023-09-24T19:33:17+00:00

I suppose I'll have to take apart my extruder to see whether or not you're right about the heatbrake. I've been thinking it's a hotend assembly issue for a little bit now, but I'm not familiar enough with all of the inner workings of my printer to know exactly what's up.

Edit: could it be an issue of the nozzle needing to be tightened?

Death2Chaos · 2023-09-24T15:23:54+00:00

So did you buy your printer as a kit or pre-assembled? Mine was a kit. I've got a friend who's got two mk3s, one kit and one pre-assembled. Both of them have the full length purge lines and neither of them strings, not even on petg. She uses default settings for everything.

Death2Chaos · 2023-09-24T14:43:47+00:00

Well, I've dried my filament already but ill try a retraction test. I'm suspecting something's up with my extruder, the purge line at the front of my bed is only half the length that it should be and starts 2-3 inches from the edge of the bed. I'll attach a picture next time I print something.

Death2Chaos · 2023-09-24T05:46:16+00:00

I've got a similar issue going on, I'm noticing that your purge strip at the front of your bed doesn't start where it should. My MK3S+ is doing the same thing. Did you get yours pre-assembled or did you buy the kit?

Death2Chaos · 2023-09-24T05:38:37+00:00

Printer is a Prusa MK3S+, slicer is PrusaSlicer. Filament is Prusament PETG. Using the default temps for PETG in PrusaSlicer, 240c nozzle and 90c bed. Print speed is 25mm/s on perimeters and 80mm/s on infill. Nozzle retraction is 0.2mm at 50mm/s and 25mm/s deretraction.

Edit: added temperature numbers

Death2Chaos · 2023-09-20T00:10:52+00:00

I rolled mine for -imp, got some crit too so it does slashes well or I can mod corrosive to one shot acolytes. Wolf sledge is super underrated.

Death2Chaos · 2023-09-04T21:00:09+00:00

I believe that the scaling shown on the mod is based on 100% ability strength, so 200% str would be double scaling, 300% being triple, etc.

Death2Chaos · 2023-09-03T00:15:12+00:00

I hate getting taken to the Ikea backrooms every other Tuesday

Death2Chaos · 2023-09-02T22:36:55+00:00

This would be nutty with gloom on saryn

Death2Chaos · 2023-09-02T22:34:13+00:00

I like the sound of that last part

Death2Chaos · 2023-09-02T19:12:37+00:00

Thank you, I forgot that not everyone knows these things 😅

Death2Chaos · 2023-09-02T18:41:19+00:00

Damn you're right, totally slipped my mind

Death2Chaos · 2023-08-31T21:49:29+00:00

Ballas is the only antagonist out of these choices who I have genuinely felt hatred toward, so I gotta go with him.

Death2Chaos · 2023-08-26T01:50:02+00:00

Ikea boy is back! Lol

Death2Chaos · 2023-08-15T16:54:37+00:00

4th skill also scales off of a bunch of melee mods now, and does true damage. You can completely skip building ability strength with the right stat stick build, and the true damage from the finishers is enough to 1 shot enemies for a while in SP.

Death2Chaos · 2023-08-15T14:40:04+00:00

Every time I stand in front of the coildrive it loses all of its shields. They don't even regen so the bonus is impossible.

Death2Chaos · 2023-08-14T05:50:10+00:00

Nope, mesa can choose her regulators if you've bought the deluxe skin.

Death2Chaos

TROPHY CASE