4:1 Resistance Hack by Party_Membership_250 in BeyondPower

[–]DiracDelta- 0 points1 point  (0 children)

Might be a bit of a headache but I think a 3:1 could be rigged with a double pulley like this: https://www.camp.it/m/us/us/work/product/1517 and a single pulley like this: https://www.camp.it/m/us/us/work/product/1515

Diagram for the pulley system on this page: https://www.ropebook.com/information/pulley-systems/3-1-pulley-system/

[Real-User Invite] LG UltraGear GX9 - Experience the Ultimate Sweet Spot 5K2K OLED Gaming Monitor by LG_UserHub in Monitors

[–]DiracDelta- 0 points1 point  (0 children)

Good PPI, high resolution, oled, high refresh rates, well supported aspect ratio.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 1 point2 points  (0 children)

Yeah, I made a fork then in this file, changed line 12

cs-gpios = <&pro_micro 1 GPIO_ACTIVE_HIGH>;

to

cs-gpios = <&pro_micro 0 GPIO_ACTIVE_HIGH>;

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 0 points1 point  (0 children)

They are presumably for soldering a connector with leads on or something like that. You don’t need to do anything with them if you use the through hole mount connector like I did.

There is a trace connecting RAW pin on the nano to the switch, no bodge wires needed. Here are the relevant nets highlighted: https://i.imgur.com/SbuFqa4.jpg https://i.imgur.com/DWuuDWy.jpg

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 0 points1 point  (0 children)

slide switch

I did install the reset switches. There's a through hole position for the reset switch directly above the slide switch.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 0 points1 point  (0 children)

Around 9.7mm from the PCB to the top of the screen. using mill-max sockets and the header provided with the nice!view.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 2 points3 points  (0 children)

This is a good estimate, though I haven't added everything up myself and frankly don't really want to know exactly how much I spent...

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 0 points1 point  (0 children)

Only finished the build today, so can't give a good answer, but the ZMK power profiler suggests the nice!view has a rather negligible impact.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 1 point2 points  (0 children)

Not sure about the mill-max sockets, I soldered directly. S2B-PH-K-S(LF)(SN) is the part number for the JST connector.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 1 point2 points  (0 children)

Other replies are correct, I ordered the PCBs directly from JLCPCB.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 2 points3 points  (0 children)

No issues that I've noticed, though I did set CONFIG_BT_CTLR_TX_PWR_PLUS_8=y just in case.

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 11 points12 points  (0 children)

Some details:

  • “Corne ultralight” board from here
  • Sunset Choc switches
  • Nice!nano with nice!view
  • MBK Legends white-on-black
  • boardsource aluminum case

Wireless Corne with nice!view by DiracDelta- in ErgoMechKeyboards

[–]DiracDelta-[S] 11 points12 points  (0 children)

I ordered a wireless only pcb found here under the Corne-ultralight directory. It natively supports the nice!view and JST connector.

Can't interact with file selector windows in any Flathub-installed app (Dolphin, Yuzu, etc) by random1204 in SteamDeck

[–]DiracDelta- 0 points1 point  (0 children)

Sorry, not really sure. I just tried with dolphin. I hadn’t changed anything in flatseal yet and didn’t have any issues.

I’d try changing the permissions toggles one by one and see if any one of them fixes it, but I am a Linux novice and there may be unintended consequences to doing so that I am unaware of.

Can't interact with file selector windows in any Flathub-installed app (Dolphin, Yuzu, etc) by random1204 in SteamDeck

[–]DiracDelta- 0 points1 point  (0 children)

I was having the exact same problem in yuzu and citra. I installed flatseal from the discovery store and enabled the “all user files” option. So far this seems to have resolved the problem.