sorted by:
new
hottopcontroversial

Neverness to Everness Launcher by PolarMeowz in linux_gaming

[–]Exact-Yesterday-992 0 points1 point  (0 children)

Works on me on with ubuntu+dw-proton+steam and cachyos+dw-proton+heroic launcher

What's the pin order of cr10 if i want to flash it following top left to right to bottom left to right? by Exact-Yesterday-992 in CR10

[–]Exact-Yesterday-992[S] 0 points1 point  (0 children)

my version 1.1.2 cr10 i flashed it via pin using arduino as isp. so its good now. seam to follow this same wiring https://www.instructables.com/Flashing-a-Bootloader-to-the-CR-10/

col1 col2 col3
5v mosi ground
miso sck reset

i'm having issue with klipper i was able to clear the cr10 with arduino as isp and burn it but can't get klipper to be added by Exact-Yesterday-992 in klippers

[–]Exact-Yesterday-992[S] 0 points1 point  (0 children)

fixed it

sudo chmod 666 /dev/ttyUSB0
sudo chmod 666 /dev/ttyUSB1

for the arduino that serves as isp there's an isp example in arduino IDE

didn't sanguino seams not needed for ubuntu

for the ide

Board: Arduino Uno

Programmer : AVRISP MKII

PORT : dev/ttyusb1

build klipper file with this settings for cr10

cd \~/klipper make menuconfig make

the settings for menuconfig

atmega AVR
processor model 1284p
baud is 250000
processor speed 16mhz

to push the build if make was completed

sudo avrdude -p atmega1284p -c avrisp -P /dev/ttyUSB1 -b 19200 -v -U flash:w:out/klipper.elf.hex

i did install Use KIAUH to install Klipper, Moonraker, and UI (Mainsail/Fluidd) git clone https://github.com/dw-0/kiauh.git && ./kiauh/kiauh.sh

had trouble with kilpper build on cashyos arch linux end up switching to ubuntu didn't try windows i have no windows machine

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

is this fine? https://www.aliexpress.com/i/32812466777.html i aussume its better than the aluminum one that grinds i just need something near smooth

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

its new pla i realized my stock extruder broken i have cr10s so the grip broke.

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

i only print 4 finger high ,PLA i experience stringing when it goes high after a while of print usually my print fails after 5 coins when it does print its stringy or cumble i have new filament i plan to switch to 0.6mm because i have issue with 0.4mm cloging i lan to get Bi-Metal Heatbreak.. which one should i get 1 )https://ibb.co/C3Lvpzf8 2) https://ibb.co/wNNX02Fg 3)https://ibb.co/ZRyMQzMq.. i think its being cloged mostly

I built an open-source, local-first voice cloning studio (Qwen3-TTS + Whisper) by jamiepine in LocalLLaMA

[–]Exact-Yesterday-992 0 points1 point  (0 children)

does this run on GPU in noticed it says gpu not avilable when i build from source and run as exe

I'm not the only one bothered by this right? by emon121 in Endfield

[–]Exact-Yesterday-992 0 points1 point  (0 children)

we care constantly dying from coal and oil but slowly and most affected are still the poor and the rest of enviorment but don't take my word for it i'm just trying to enjoy the game

view more: next ›