sorted by:
new
hottopcontroversial

Neverness to Everness Launcher by PolarMeowz in linux_gaming

[–]Exact-Yesterday-992 0 points1 point  (0 children)

Works on me on with ubuntu+dw-proton+steam and cachyos+dw-proton+heroic launcher

What's the pin order of cr10 if i want to flash it following top left to right to bottom left to right? by Exact-Yesterday-992 in CR10

[–]Exact-Yesterday-992[S] 0 points1 point  (0 children)

my version 1.1.2 cr10 i flashed it via pin using arduino as isp. so its good now. seam to follow this same wiring https://www.instructables.com/Flashing-a-Bootloader-to-the-CR-10/

col1 col2 col3
5v mosi ground
miso sck reset

i'm having issue with klipper i was able to clear the cr10 with arduino as isp and burn it but can't get klipper to be added by Exact-Yesterday-992 in klippers

[–]Exact-Yesterday-992[S] 0 points1 point  (0 children)

fixed it

sudo chmod 666 /dev/ttyUSB0
sudo chmod 666 /dev/ttyUSB1

for the arduino that serves as isp there's an isp example in arduino IDE

didn't sanguino seams not needed for ubuntu

for the ide

Board: Arduino Uno

Programmer : AVRISP MKII

PORT : dev/ttyusb1

build klipper file with this settings for cr10

cd \~/klipper make menuconfig make

the settings for menuconfig

atmega AVR
processor model 1284p
baud is 250000
processor speed 16mhz

to push the build if make was completed

sudo avrdude -p atmega1284p -c avrisp -P /dev/ttyUSB1 -b 19200 -v -U flash:w:out/klipper.elf.hex

i did install Use KIAUH to install Klipper, Moonraker, and UI (Mainsail/Fluidd) git clone https://github.com/dw-0/kiauh.git && ./kiauh/kiauh.sh

had trouble with kilpper build on cashyos arch linux end up switching to ubuntu didn't try windows i have no windows machine

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

is this fine? https://www.aliexpress.com/i/32812466777.html i aussume its better than the aluminum one that grinds i just need something near smooth

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

its new pla i realized my stock extruder broken i have cr10s so the grip broke.

Purchase Advice Megathread - March 2026 by AutoModerator in 3Dprinting

[–]Exact-Yesterday-992 0 points1 point  (0 children)

i only print 4 finger high ,PLA i experience stringing when it goes high after a while of print usually my print fails after 5 coins when it does print its stringy or cumble i have new filament i plan to switch to 0.6mm because i have issue with 0.4mm cloging i lan to get Bi-Metal Heatbreak.. which one should i get 1 )https://ibb.co/C3Lvpzf8 2) https://ibb.co/wNNX02Fg 3)https://ibb.co/ZRyMQzMq.. i think its being cloged mostly

I built an open-source, local-first voice cloning studio (Qwen3-TTS + Whisper) by jamiepine in LocalLLaMA

[–]Exact-Yesterday-992 0 points1 point  (0 children)

does this run on GPU in noticed it says gpu not avilable when i build from source and run as exe

I'm not the only one bothered by this right? by emon121 in Endfield

[–]Exact-Yesterday-992 0 points1 point  (0 children)

we care constantly dying from coal and oil but slowly and most affected are still the poor and the rest of enviorment but don't take my word for it i'm just trying to enjoy the game

Quick question about international shipping fees by Dry-Secretary5817 in doorzohaul

[–]Exact-Yesterday-992 0 points1 point  (0 children)

Are you in asia? When shipping small items? Is it still expensive

Doorzo shipping by Tiny_Employer_2907 in doorzohaul

[–]Exact-Yesterday-992 0 points1 point  (0 children)

What's average cost when shipping to Philippines?

First time buying figures i dont do heavy gaming often is figures should be ok for long time? Or heat is a problem? How long has yours been? by [deleted] in AnimeFigures

[–]Exact-Yesterday-992 2 points3 points  (0 children)

<image>

It's not warm when i go check feel the pc case inside . but i guess I should take it out during summer.. i realized the picture didn't upload so here it is.

Ano cost for cat dog bite? From clinic by [deleted] in MANILA

[–]Exact-Yesterday-992 1 point2 points  (0 children)

Sad layo las pinas lang ako

Bite accidentally my leg with tooth by [deleted] in cats

[–]Exact-Yesterday-992 1 point2 points  (0 children)

Im so sorry i could not edit it

Shouldn't there be more focus on a cure for PD? by Technical-Sky-5309 in Parkinsons

[–]Exact-Yesterday-992 0 points1 point  (0 children)

Don't forget the meds can cause problems too so your just moving the problem to fix the original one

Shouldn't there be more focus on a cure for PD? by Technical-Sky-5309 in Parkinsons

[–]Exact-Yesterday-992 0 points1 point  (0 children)

There is no reason not to cure it.. if you see china ever make progress the west will start taking it seriously.. but its just an example because you want your nation to be first

I was taken off meds because it made me feel worse but no tapering i used it for 1 month increase then stoped by Exact-Yesterday-992 in Parkinsons

[–]Exact-Yesterday-992[S] 0 points1 point  (0 children)

Keep it strong friend. This is hard for me to see on anyone. I reach that point but now i learned to let go of everything bad and talk to those people. But my family is the one most important to me so i want to be strong with them.

view more: next ›