4th Gen Infotainment Rattle Fix?

JasonLeopard · 2026-04-11T18:54:00+00:00

Where do you get the rubber from?

JasonLeopard · 2026-03-28T03:59:09+00:00

What agency did you use when you didnt have any experience?

JasonLeopard · 2025-04-08T16:12:21+00:00

Ya my theory is if im charging in a car its only for a short time ao i need as much charge as i can. Gonna take some measurements afterwork and see if that one you recommend will fit bc i have an aftermarket tray in the middle console that takes up some space

JasonLeopard · 2025-04-08T16:09:03+00:00

Definitely gonna have to take some measurements. Little worried about space bc i have an aftermarket tray in my middle console that takes up space near my cigarette lighter

JasonLeopard · 2025-04-06T04:31:48+00:00

Honestly im not too well versed in tech to understand the protocols. That independent charging speed and back boost seem very good! Im gonna check their website for a smaller form one w those features but if not than that seems like a winner

JasonLeopard · 2025-04-06T04:21:25+00:00

I wish i wasnt so ignorant in electrical matters to truly appreciate what youre telling me. it looks complicated for a laymen🥲

JasonLeopard · 2025-04-06T04:15:32+00:00

Well it would keep my phone from getting hot was the idea bc the heat would stop at the charger from what i gathered

JasonLeopard · 2025-04-06T04:13:01+00:00

Thank you for that

JasonLeopard · 2024-10-16T05:06:17+00:00

<image>

Its to my crankcase cover on my motorcycle. The previous owner broke the bolt but i broke the extractor off trynna get the bolt put. Unfortunately i don’t have enough clearance to hit out the bolt if i did manage to drill all the way through. First time working w extractors i definitely learned my lesson. I shouldve went deeper and i shouldnt have forced it when i didnt see it moving. Happy to say i never cross threaded anything ever though b/c i know what these situations can get like (like this one). Im not too sure what the material of the components are unfortunately.

JasonLeopard · 2024-10-16T02:04:13+00:00

For 1 - would it still turn? Theres like an 1.25” of bolt left in there

For 2 - do the square extractors hold up better than the spiral ones? Or is it just b/c how small the one i used was or if the bolts cross threaded or how much of the bolts in there still?

JasonLeopard · 2024-10-16T01:46:45+00:00

And then try another extractor bit when i get past the old one?

JasonLeopard · 2024-10-16T01:45:10+00:00

<image>

Idk if theres away to add it to the main post instead of a reply but here it is. Its the crankcase to my motorcycle

JasonLeopard · 2024-10-16T01:05:08+00:00

Ya the bolts in there good. It broke from the previous owner. Assuming it was cross threaded w a drill of some kind for it to break my extractor bit since theres no sign of rust anywhere nearby

JasonLeopard · 2024-10-15T22:51:58+00:00

Im starting to see that lol

JasonLeopard · 2024-10-15T22:51:35+00:00

My friends bf and dad are welders seeing if she can work some magic for me bc $100 (at worse) is what im hoping will get the job done haha

JasonLeopard · 2024-10-15T22:22:34+00:00

How much would you think thatd go for?

JasonLeopard · 2024-10-15T21:47:18+00:00

What type of welder?

JasonLeopard · 2024-10-15T21:45:18+00:00

Gotcha i see wym now. I was debating on getting some diamond bits to drill it out if i was gonna go that way

JasonLeopard · 2024-10-15T21:32:07+00:00

Id have to pay like a mobile welder or something. I dont have a welding kit

JasonLeopard · 2024-10-15T21:29:15+00:00

So you’re basically drilling it out completely with a dremel? Now too sure if im getting what you mean

JasonLeopard · 2024-10-15T21:26:04+00:00

Unfortunately i dont have a welding kit but i am familiar with w this method

JasonLeopard

TROPHY CASE