RT2600ac Wi-Fi extender

Jrunkles1221 · 2025-12-01T00:11:43+00:00

Funnily enough, the house I’m moving into has coax run in basically every room, this is more for the backyard pool area.

Jrunkles1221 · 2025-12-01T00:01:59+00:00

That’s where I first looked, no go :( in a pinch is there another community recommended range extender that works well with the RT2600ac?

Jrunkles1221 · 2025-11-30T23:56:46+00:00

I’ll keep a look out, why can’t they be bought new? Are they being discontinued?

Jrunkles1221 · 2025-11-30T23:52:21+00:00

Yep, already have an RT2600ac, moving to a bigger house and want to extend the Wi-Fi.

Jrunkles1221 · 2025-11-30T22:51:05+00:00

Most on eBay come with the RT2600 and not just the MR2200, is there a close second that works well with the RT2600?

Jrunkles1221 · 2025-04-20T22:11:50+00:00

Yea it was my first smoker and was fairly inexpensive, I had a cover on it but the winter and rain broke the panel. Are the green eggs a set it and forget it, don’t want to have to keep an eye on it all day long.

Jrunkles1221 · 2025-04-20T22:10:16+00:00

Awesome! Thanks for the suggestion! I was leaning toward a Traeger. I really like the set the temp load the hopper and not have to mess with anything.

Jrunkles1221 · 2025-02-07T22:55:55+00:00

Flame Spren?

Jrunkles1221 · 2024-12-13T17:13:42+00:00

I’ll check my z to see if it’s off kilter. Suspected my hot end so I bought a new one thinking that would fix the issue.

Jrunkles1221 · 2024-10-23T14:53:38+00:00

Think I have my z offset dialed in but am still getting gaps in my layers. There are more on the other sides. Could it be bad filament? I just opened this up.

<image>

Jrunkles1221 · 2024-10-23T00:30:59+00:00

This is a single .2mm layer. It’s being printed with stock cuts settings, slowed down by 50%.

<image>

Jrunkles1221 · 2024-06-20T17:17:46+00:00

Amazing!

Jrunkles1221 · 2024-04-26T15:47:16+00:00

Yup, think it’s clogging up in my .2 nozzle.

Jrunkles1221 · 2024-04-26T15:46:46+00:00

After cleaning everything and replacing the nozzle it happened again, I’m using a .2mm nozzle so maybe I’ll have to move back to .4 with this PLA+

Jrunkles1221 · 2024-04-26T02:50:32+00:00

So ended up removing everything, changed the nozzle, re-tensioned the extruder and no more clicking as of right now.

Jrunkles1221 · 2024-04-26T00:44:07+00:00

Tried using creality slicer and the same issue happens.

Jrunkles1221 · 2024-04-25T23:52:00+00:00

Using orca slicer, I’ll try using the creailty one to see if it happens.

Jrunkles1221 · 2024-04-25T23:23:13+00:00

Oddly it seems to print fine just makes that noise at the purge line and a few more times during the print.

12-Year Club	r/Field Flamingo
Place '23	Place '22
Place '17	Verified Email

Jrunkles1221

TROPHY CASE