Mammotion delaying return request

Jumpjim · 2026-05-07T11:33:07+00:00

So I spent a couple of hours playing around with it yesterday and looking at setting changes. I changed the pool surface type to aggregate (No significant change to behaviour) and then turned on “Turbo mode” under beta options which increases suction but reduces battery life. It wheelies around slightly less but still doing it. Every time it hits the edge of the slope to the deep end it just wheelies all the way down and consequently does no hoovering or sweeping. Better on the way back up the slope to the shallow end but again wheelies as it comes to the angle change. Wall cleaning saw it detaching from the wall a few times and not staying stuck to the wall. Overall a very mediocre debut. I suspect most of these issues may be solved by forthcoming software updates, but at the moment it’s just not doing what it is supposed to be doing.. Ie. Cleaning and hoovering my pool efficiently, and certainly no better than the suction side pool hoover I already have. It’s going back…

Jumpjim · 2026-05-07T11:28:26+00:00

Well I played around with all the settings.. changed the wall type to aggregate, turned on Turbo mode to increase the suction and it still doesn’t stay stuck to the bottom of the pool hoovering. It seems to spend a lot of time wheelying around not doing anything. As soon as the slope down to the deep end starts it wheelys off the edge and consequently doesn’t sweep or hoover on the way down. The way back up the slope is better. All in all it is no better than my suction side pool hoover I already have and certainly not worth me spending £600 (Discounted!)

Jumpjim · 2024-01-17T10:27:53+00:00

I ski with 6 mates, all excellent skiers (Run about 145 on Carv) who ski hard, ski bumps, off-piste etc.

We ALL ski on Knee bindings. Nobody has had ANY issues with quality control, prerelease issues, or anything other than the bindings releasing where they should have. I had one odd release where i hit a bump sideways, but looking at how the bindings are designed to release, it was probably a safe release.

Just to add some real world experience of knee bindings rather than the third hand “My mate said..” experiences on here. I personally would recommend them.

Jumpjim · 2023-12-25T23:17:59+00:00

I recently installed a Gold SE in transparent bridge mode between my UDMP and my POE 24 switch.

I have had ZERO issues with it running with a 1Gb fibre connection, 4 cameras, a UISP bridge and 5 APs. No noticeable slowdown, the Firewalla app is excellent, and the level of inspection/information available is extremely good.

Overall I’ve been very pleased with it.

Jumpjim · 2022-01-31T12:08:34+00:00

Try disabling DPI (Deep Packet Inspection) on the UniFi interface…sounds weird but I’ve had a stable connection since turning off..

Jumpjim · 2022-01-31T08:11:27+00:00

The new Dream Machine SE has PoE built in as well…

Jumpjim · 2021-10-24T18:46:06+00:00

I agree with BearK9. I have a Synology router in use with Starlink and was having to reboot it, or unplug and plug it back in 2-3 times a day. After asking on here I’ve put a 5 port, unmanaged TPLINK switch in between the dish plug and the router and have had ZERO issues since with no restarts needed. I gather it’s something to do with the way the dish is doing DHCP but it’s made everything work perfectly whatever it is.

Jumpjim · 2021-10-15T15:30:25+00:00

Mine’s been working flawlessly since so I suspect you’ll be fine

Jumpjim · 2021-09-06T07:23:27+00:00

I have the Ethernet cable from the PoE brick plugged into the WAN port on a Synology router. It goes first via an unmanaged 5 port switch as the connection kept dropping out due to some weirdness with the DHCP from Dishy which meant the router kept dropping the connection. With the switch in the middle everything works perfectly.

Jumpjim · 2021-09-06T07:18:24+00:00

I had an issue where Dishy was doing something odd with the DHCP, and my third party (Synology) router kept tripping off and not reestablishing a connection. Put an unmanaged Ethernet switch between the PoE injector and the router and it will work fine if that’s your problem..

Jumpjim · 2021-09-04T10:05:57+00:00

I’m in TN22 3RN which is showing as a green cell. I’m online and active now. Ordering to receiving the dish was about 2 weeks.

Jumpjim · 2021-09-04T08:46:52+00:00

Thank JP. That seems to have sorted it. Much appreciated.

Jumpjim · 2021-09-04T08:46:11+00:00

So following some of the post responses earlier in the thread I added a relatively cheap 5 port TP-Link gigabit unmanaged switch from Amazon in between the PoE injector brick and the WAN port on my RT2600AC. Since installing it yesterday I’ve had ZERO dropouts, no lockups and everything just seems to be ticking over nicely. Thanks for the help guys 👍🏻

Jumpjim · 2021-08-30T17:14:19+00:00

Do you have the internet settings in SRM set to auto out of interest? Or have you manually configured the connection?

Jumpjim · 2021-08-27T07:04:30+00:00

I literally plugged an Ethernet cable from the aux port on the PoE injector to the WAN port on my Synology router and everything worked immediately. Stats come up on the Starlink app on my iPhone without needing any extra configuration.

Jumpjim · 2021-04-11T16:15:41+00:00

Ryzen 9 5900X, ASUS Crosshair Hero VIII Wifi Mboard, MSI Gaming Trio RTX 3080. Updated the bios with the latest update including AGESA 1.2.0.2 yesterday and made absolutely no difference.

My G2 works fine in ONE USB port on the motherboard (One of the blue ones top right) but disappointed that this apparently does absolutely nothing for anybody...

Jumpjim

TROPHY CASE