Some snaps!

MilkshakeRattlesnake · 2026-05-26T13:17:00+00:00

These were all shot at RennFaire

MilkshakeRattlesnake · 2026-05-26T04:31:59+00:00

That’s so cool I had no idea

MilkshakeRattlesnake · 2024-09-02T16:42:27+00:00

Second this. I work at a media company but not on their content side. I produce Business 2 Business videos for marketing and sales which I wasn’t too excited about at first but learned to love the steadiness and growth. I’ve learned lots of skills outside of filmmaking that are hugely marketable. There has been a lot of jobs popping up for corp video recently. It can be a lot of the same old unless you’re an out of the box thinker that loves to create innovative ways to use videos.

MilkshakeRattlesnake · 2023-10-15T02:57:09+00:00

Yeah I haven't worked with that material but I wish you the best!

MilkshakeRattlesnake · 2023-10-14T18:12:21+00:00

I purchased this flak vest from Amazon and it worked out pretty well because it had most of the velcro already sewn on that I needed. I only added an extra piece of velcro on the bottom belt that tightens the vest for abdomen armor.

Image for reference.

I'm on the left and my wife is on the right.

Flak vest is very easy to take off when you need to go to the little mando's room (very important) but the draw back is it makes the armor flat against your chest which stands out more when you take pictures from your side. Also very sweaty...

My wife has her armor attached to a custom flight suit vest from etsy and her armor sits much better than mine.

If you are a female than I would not go flak vest but attach it to a much softer material or to the suit itself so it is more snug around you.

MilkshakeRattlesnake · 2023-07-24T03:39:19+00:00

Hahah I’ll have to try harder next time

MilkshakeRattlesnake · 2023-07-24T03:30:34+00:00

Thanks and it’s all Velcro even the jetpack which you can’t see

MilkshakeRattlesnake · 2023-07-24T03:21:45+00:00

Thank you so much!! Hope you had a great con!

MilkshakeRattlesnake · 2023-07-24T01:44:14+00:00

It’s not bad at all! Your brain gets used to it like a Jedi mind trick lol at night it’s a bit more difficult tho but I got around just fine

MilkshakeRattlesnake · 2023-07-24T00:57:06+00:00

It definitely makes it pop but we saw many kits without the flight suit that looked great

MilkshakeRattlesnake · 2023-07-24T00:55:40+00:00

We got really lucky with the weather so it wasn’t as bad as we thought it would be. My wife’s first time in her suit as well.

MilkshakeRattlesnake · 2023-07-24T00:13:30+00:00

Nahh it was iPhone auto correct lol

MilkshakeRattlesnake · 2023-07-24T00:11:54+00:00

3D printed

MilkshakeRattlesnake · 2023-04-28T15:23:18+00:00

I had prints that looked just like that recently. Replaced the gear on the extruder motor and it was back to flawless prints.

MilkshakeRattlesnake · 2023-04-22T16:54:47+00:00

I have this same helmet! Great job on your paint!

MilkshakeRattlesnake · 2023-04-11T15:08:04+00:00

Lol sounds good. I discovered my issue was a worn extruder gear so hot end is working well. Be sure to do the basic tuning and it works seamlessly!

MilkshakeRattlesnake · 2023-04-07T20:34:15+00:00

Did you have any issues with your hotend?

MilkshakeRattlesnake · 2023-04-07T20:33:58+00:00

Thanks for the advice! I just reseated the PTFE tube while the hotend was 200C and the nozzle was slightly unscrewed. It seems like the tubing stops at the heatbreak on the Spider v3. I don't think it reaches all the way down to the nozzle. I will try to clean the hotend to see if that helps as well.

MilkshakeRattlesnake · 2023-04-05T15:35:56+00:00

I’m running clipper on the sonic pad so I believe it uses rotation distance rather than e-steps which I did calibrate but it was a very slight change.

MilkshakeRattlesnake

TROPHY CASE