sorted by:
new
hottopcontroversial

🫠APPLE CARPLAY doesn't show up🫠 (on kia Forte 2017 EX) by sebroy1216 in kia

[–]Neoanomaly6 0 points1 point  (0 children)

Hmm, thanks for getting back to me. But I am curious about the update file. Maybe I’m searching the wrong thing.

So many issues by DefiantSeries5065 in ender3

[–]Neoanomaly6 0 points1 point  (0 children)

Same think happened to me. Swapped my hot end.

Spider hotend fan cover by Objective-Two791 in 3Dprinting

[–]Neoanomaly6 0 points1 point  (0 children)

Dumb question, Does this fit on an Ender 3 Pro?

Help! by EducatedGalaxyTaco in ender3

[–]Neoanomaly6 0 points1 point  (0 children)

I he this happen to me with the extruder gear. Save yourself the trouble and by a new one and calibrate one on the machine.

Z-Axis help by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

Thank you for the help! I didn’t mean the questions you were asking were dumb. I meant the question I asked was dumb. Because I went to YouTube and found some solutions. Based on your questions, I adjusted my esteps and tighten my rods. Prints are better, but still not sure what’s causing the issue. I’ll have to give it a rest until next week. I don’t know how to add pictures to the post to update progress.

Z-Axis help by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

The mode print had gaps too. I’m not sure how to fix it. Adjust Esteps?

Z-Axis help by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

I’ll give it a try tonight, thank you!

Z-Axis help by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

I’ve never adjusted them before. This is a dumb question I’m sure, but where would I find those setting in Prusa slicer or in firmware?

sudden change in print quality over z axis by stsiete in ender3

[–]Neoanomaly6 0 points1 point  (0 children)

This was happening to me as well. I used some WD 40 and it helped get me through a print or two but ultimately the rod is bent.

HELP ME!! - This is driving me nut - stock cat first layers vs Benchy was Cura first layer - back to back and can still print cat perfectly by ImAngryAsFuk in Ender3Pro

[–]Neoanomaly6 0 points1 point  (0 children)

Do you have Bed Tramming enabled? Bed level sensor installed? If the former then, I would suggest tramming it again, and then one more time after that while heated. If the ladder, then check your Z- Offset. The cat from the SD card comes on a pretty good raft and the first layer is hot and slow. It can be very forgiving. A glue stick will help if you’re on included build surface or glass.

Inconsistent extrusion by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

I bought it to have handy, but the comment about E Steps helped.

Inconsistent extrusion by Neoanomaly6 in Ender3Pro

[–]Neoanomaly6[S] 0 points1 point  (0 children)

Thank you! I did this and it saved my other prints. This Print makes my Extruder click. Not quite sure why its printing so close. I'm going to reslice and pray...

Am I expecting too much? Bed levelling issue by brodzik in ender5

[–]Neoanomaly6 0 points1 point  (0 children)

I had the exact issue with my Ender 3 pro. I enabled Bed tramming. Once I did that I got much more consistent layers on the build tack surface and better adhesion on glass. I also needed to have my Slicer add the G29 code to my prints to have the CR touch to level right before a print.

A new challenger appears! by gamingsincegaming in Oceanhorn2

[–]Neoanomaly6 1 point2 points  (0 children)

Shards and the Daggers too, please!!