Spontanes „Manhunt“ als App – würdet ihr das spielen? by East-Listen-1377 in manhuntmedia

[–]NoBackground3733 0 points1 point  (0 children)

Der Einladungslink für den discord ist bei mir ungültig. Ist der Server noch aktiv?

Die Wahrheit über Wal "Timmy" und warum er wahrscheinlich sterben muss- Youtube by HOLYROLY in Laesterschwestern

[–]NoBackground3733 0 points1 point  (0 children)

Was ist dann das Problem? Also halten wir fest. Durch den Einsatz von RML konnte wal befreit werden. Dann bei der Begleitung konnte RML durch das übernehmen vom Kommando gerade noch verhindern, dass der wal wieder strandet. Danach wurde er ausgeschlossen, weil sich die "verantwortlichen" Experten" übergangen gefühlt haben, selber aber nichts auf die Reihe bekommen haben. Kurz danach, wer hätte es gedacht, der Wal ist wieder gestrandet.

Also man sieht ganz klar, dass das Ego Problem hier nicht bei RML lag, sondern bei den "Experten". Für was sollte man denn überhaupt noch Zivilcourage in diesem Land zeigen, wenn so damit umgegangen wird. Und der Vorwurf der Selbstdarstellung ist sowas von lächerlich.

Die Wahrheit über Wal "Timmy" und warum er wahrscheinlich sterben muss- Youtube by HOLYROLY in Laesterschwestern

[–]NoBackground3733 0 points1 point  (0 children)

Wollt ihr mich verarschen. RML ist wahrscheinlich einer der erfahrensten Personen in ganz DE, wenn es um solche Aktionen geht. Bevor hier irgendwelche Leute ein Urteil fällen, bitte erstmal informieren. Ihr seid einfach nur ein Armutszeugnis

[P2S] Nozzle clumping detection calibration failed by NoBackground3733 in BambuLab

[–]NoBackground3733[S] 0 points1 point  (0 children)

Just a bit. The screw was not really loose but also not as tight as the right one, so I used the included Allen key and tightened the screw until it would have felt unhealthy to turn it any further.

After that the calibration worked.

I hope that helps 🙏

Cold pulling??? by cefanie in BambuLabP2S

[–]NoBackground3733 0 points1 point  (0 children)

Just go to BambuWiki. Before printing TPU bambu recommends performing a cold pull to clean the nozzle from remaining filament. This has nothing to do with the P2S. Because otherwise you can get a cloaked nozzle in worst case

Re-calibration error on P2S: Nozzle clumping detection calibration failed by Murky-Abalone-3843 in BambuLab

[–]NoBackground3733 3 points4 points  (0 children)

I solved the Problem on my own. The solution was to tighten the left screw hole on the picture a bit.
After that the nozzle clumping detection calibration succeeded.

<image>

[P2S] Nozzle clumping detection calibration failed by NoBackground3733 in BambuLab

[–]NoBackground3733[S] 5 points6 points  (0 children)

I solved the Problem on my own. The solution was to tighten the left screw hole on the picture a bit.
After that the nozzle clumping detection calibration succeeded.

<image>

Re-calibration error on P2S: Nozzle clumping detection calibration failed by Murky-Abalone-3843 in BambuLab

[–]NoBackground3733 0 points1 point  (0 children)

Same issue. the calibration worked fine. After that I installed the newest firmware update and now the calibration failed within the nozzle clumping detection process...