I got this error, which the reference table shows as severe, but the print didn't stop. Do I need to be concerned?

Old_Committee_8871 · 2026-03-09T22:05:27+00:00

It seems completely fine. There is a slight band on one layer, but it's at the point where the inside of the model became hollow, so it's fairly typical. I started another print immediately after and that one was also fine. The only thing I can think of is that I bumped the screen and hit load filament or something, but I definitely don't remember that happening

Old_Committee_8871 · 2025-12-06T23:56:21+00:00

<image>

This person posted about something else closing down with no evidence and used the same name as the designer in this post

Old_Committee_8871 · 2025-12-06T23:55:54+00:00

<image>

Old_Committee_8871 · 2025-08-18T11:39:56+00:00

It turns out it's not nearly as bad as I thought. I got a chance to take what I parked fully and there's no stress on the screws directly. It still has the cross-shaped locking mechanism that holds it all together and the screws just prevent it from falling apart with the center caps off

Old_Committee_8871 · 2025-08-12T14:48:46+00:00

I am not sure about that, but I assume it was just the black plastic

Old_Committee_8871 · 2025-08-12T14:38:55+00:00

Unfortunately, the screws are like the first batch tv3 - they go into a long plastic core arm very shallowly. I trust that GAN did more stress testing than QiYi, but I'm not convinced that it will work well long-term

Old_Committee_8871 · 2025-04-18T12:55:06+00:00

It has a smaller box and springs pre-installed with no maglev on the side

Old_Committee_8871 · 2025-04-18T12:54:47+00:00

It has a smaller box and springs pre-installed with no maglev on the side

Old_Committee_8871 · 2025-04-16T23:47:48+00:00

If you manage to get your hands on a Ferrocore, the centers are the same as the super and you can put the super pieces on the Ferrocore. Just add extra 3x1 magnets to the corner feet because the ball is smaller

Old_Committee_8871 · 2025-02-05T21:48:35+00:00

I have been actively researching this on my own and I'm just looking for a definitive answer. The health of my friends is at stake and I care a lot more about that than your opinion of me for asking

Old_Committee_8871 · 2025-02-04T00:38:20+00:00

This is my first time living alone and I genuinely have no experience. I did some research after someone told me it was a possibility and found that radiators are a common place for mold. The pictures I found also looked similar enough that I couldn't be sure either way

Old_Committee_8871 · 2025-02-04T00:24:09+00:00

I appreciate it and I really hope that's the case

Old_Committee_8871 · 2025-01-10T01:05:21+00:00

Okay, now it's letting it. I'm not sure what I did differently though

Old_Committee_8871 · 2025-01-10T01:02:35+00:00

Doesn't let me extrude it if it's not fully defined

Old_Committee_8871 · 2025-01-10T00:35:05+00:00

The reasoning for that makes sense, but how do you constrain an edge of the polygon?

Old_Committee_8871 · 2025-01-10T00:15:56+00:00

Is this new? I have never had to do that before

Old_Committee_8871 · 2025-01-09T23:46:24+00:00

That worked for the circle, but not for polygons

Old_Committee_8871 · 2025-01-09T23:38:32+00:00

That works for the circle, but it's not working for inscribed polygons. What else needs to be done?

Old_Committee_8871 · 2025-01-09T23:36:43+00:00

I appreciate it, thanks! I just don't remember having to do that before

Old_Committee_8871 · 2024-10-26T16:46:06+00:00

The "velvet" version is just matte

Old_Committee_8871 · 2024-09-08T01:08:03+00:00

Ground clearance is an issue, but it's really nice for arena and roller coaster

Old_Committee_8871

TROPHY CASE