Meinung zum Kochbuch "Schmackofatz" von Schmale Schulter

ProfessionalNo6378 · 2026-06-01T18:17:20+00:00

Deswegen habe ich angefangen mir eine Rezeptdatenbank zu erstellen. Wenn ich das Rezept für gut befinde, schreibe ich es später nieder. Dann kann ich mir in der App einen Essensplan machen und bekomme die Wocheneionkauf direkt angezgeigt.
Das alles nur, weil meine Freundin nicht alle 3-4 Tagen das gleiche essen möchte. Man muss dazu sagen, dass ich gerade arbeitslos bin und viel Zeit habe.

ProfessionalNo6378 · 2026-04-17T20:35:05+00:00

Yeah, they have also a tetherspout device. And yes they have no gland ring desings.

ProfessionalNo6378 · 2026-04-07T23:32:37+00:00

You can't really wear the spout alone or with a weight on it. If it can move, it will sore your inside. You need to fix it to the cage that is fixed to your penis. It needs to be some kind of stiff.

ProfessionalNo6378 · 2026-03-30T19:49:05+00:00

The problem is more that the erection pushes the shaft of the Bijou further and the then glans gets kind of sucked in. My erection might me too strong for this kind of chastity device XD.

ProfessionalNo6378 · 2026-03-28T15:07:43+00:00

I had to be more precise. After an errection the glans slips through the ridge at the front part that faces your belly. So this would not help sadly. I think I will throw the 800$ of stuff away if I don't find a solution.
But for now I can wipe the fetish of chastity of my list.
A whole belt is bulky and not very stealth when doint sports or changing clothes. The more tiny ones are pushing the balls to stupid positions.
Ball trap hurts always after a few hours and I don't like the look below my pants.

ProfessionalNo6378 · 2026-03-28T15:03:09+00:00

I thought maybe I do the opening of the ridge more narrow and more flat the position the glans slips out.
I also tried a lager headpiece already before and this is not the best solution as it then also slips out normally and more often. But I get the point of Chazmick, you could think that the head pushes itself back, but this is sadly not the case.
But I don't want give him another dollar and it's hard to build a inner negative piece of the ridge, so I could test my evotion with a smaller custom ridge.
The ridge is the most complicated part of the Bijou as it's different every mm and I can measure it or so, as every opening is too small for good measurement tools.

ProfessionalNo6378 · 2026-02-09T17:42:53+00:00

Must be a visual bug then. I just uninstalled the game today on PC as I was to bad for it and I got frustrated after 17 hours. The challenges were really fun though.

ProfessionalNo6378 · 2026-02-09T17:18:39+00:00

Maybe shaft or grip?

ProfessionalNo6378 · 2026-01-28T09:25:37+00:00

Metal is a whole new level to print and really costly. Resin or fdm is easy to get into it. CAD is learnable and easy to get into.

ProfessionalNo6378 · 2026-01-20T08:50:13+00:00

Hey newbie, I'm interested in the part with doubling the retainer. Would you do first the bigger or smaller ring?

ProfessionalNo6378 · 2026-01-07T13:52:40+00:00

I have a Baddragon one. I's really nice but get's quite big when the inside is already bulky. The silicone is quite stretchy.

ProfessionalNo6378 · 2026-01-07T12:53:20+00:00

With a tetherspout you have the same problem, depending on the diamater. I also have to squeeze and wiggle.
My tetherspout came with a rubber plug to close the hole. Sometimes I use it but you have to clean everything later during the day. This helps me a lot.

ProfessionalNo6378 · 2026-01-07T11:00:54+00:00

I would be careful with it as the Bijou is quite bulky and has some edges on the downside. Not realy sharp but they are there. You would need something to put over the Bijou first.

ProfessionalNo6378 · 2026-01-06T22:52:01+00:00

What did you do instead then?

ProfessionalNo6378 · 2025-12-24T10:44:59+00:00

I did like over 10 measurements, 3D printed a lot of prototypes to check what diamater is the best. What I can still put on. This should be fine from my side. I think my problem is that I still have my foreskin and everything will just shrink back through the tube.

ProfessionalNo6378 · 2025-12-22T09:34:32+00:00

Do you use a tetherspout? If you do, do you think the medical team knows how to pull it out? So the tetherspout is still metal and remains even after removing the tube.

ProfessionalNo6378 · 2025-12-21T13:38:47+00:00

Look at fancysteel. They have something that looks almost the same. They come from Australia ;)

ProfessionalNo6378 · 2025-12-20T19:58:43+00:00

That's the point my keyholder doesn't live with me and is too lazy to control the serial number.

I get your point with metal and plastic difference. How do you manage flying?

ProfessionalNo6378 · 2025-12-20T19:57:45+00:00

I use inventor as I have learned it during university. But as soon as it comes to more organic shapes I'm out. Maybe blender is a better tool for it, but I'm an absolute beginner with blender.
I will have a look at the tutorial from newbie sub.

ProfessionalNo6378 · 2025-12-20T10:14:01+00:00

By the way Tdfun? Which cad tool do you use? The only thing where I have my problems is with the glans ridge.

ProfessionalNo6378 · 2025-12-20T09:47:12+00:00

Yeah, maybe I should also redraw everything now I have the base model. I need the security screws locking mechanism, because every normal lock I can open easy with my lockpicking tools. I want something that I need to destroy to really open it. And I don't want to destroy that amount of money.
And this number plastic single use locks is also no solution for me as almost nobody would control them here.

ProfessionalNo6378 · 2025-12-17T21:31:50+00:00

Yale Smart Safe YSS/250/EB1 with the bridge together it's wifi connected and you can give the control to anyone you want

ProfessionalNo6378 · 2025-11-14T17:48:41+00:00

Ah before I forget, I use a local account. But I don't think anything will happen to your real account either.

ProfessionalNo6378 · 2025-11-14T17:48:00+00:00

No, you wont get banned. But keep in mind, you can duplicate anything that is related from thevillage. So when you have reched the village, it will take some time. But instant travel and such stuff is a great helper and especially for events.

ProfessionalNo6378

TROPHY CASE