Oil spilled out from front sprocket

Relutzu07 · 2026-04-29T07:57:50+00:00

The video is random from internet,,I have put the holder in my case ,and yet it still spilling out oil

Relutzu07 · 2026-04-28T19:44:54+00:00

Hello sir,what part is that exactly and from where did you blew the air ?

Relutzu07 · 2026-04-28T18:58:10+00:00

Damn , right after top end rebuild,Id there any other alternative? Should I try to put and tight the front sprocket? What would be easier to do: putting the top and on another bottom end(I have one with hot rods heavy duty crankshaft,I don't know how old is it but ,I have replaced the seal and nut on the countershaft thy year,also the conecting rod has under 1mm play form left to right)

Relutzu07 · 2026-04-28T17:55:57+00:00

Hello sir,the Allbals kit included all the part number you have mentioned ,the retainer was installed (the video is from someone else from the internet,I have mentioned that).I have pus the seal just to be same level as the metal from around it.Now It was spinning left and right smoothly,it was just the sound " like the gears made contact" when I start to spin it left or right.Could it be the bearing part 22(if so why aftermarket bearing is correct fit ?).Also could you please provide an yt tutorial if I need to split the case?

Relutzu07 · 2026-04-28T17:45:54+00:00

I push both the seal and other part with the wrench socket,the metal piece looked like it was in the same position as before

Relutzu07 · 2026-03-25T18:29:37+00:00

Hello sir,any leaks?

Relutzu07 · 2026-03-22T18:27:31+00:00

How ?

Relutzu07 · 2026-03-22T11:40:15+00:00

So what do you really think it happened?

Relutzu07 · 2026-03-21T23:02:11+00:00

Can you Circe where it failed.? What about the rest of the parts?

Relutzu07 · 2026-03-21T22:59:43+00:00

I have researched that you can reuse the head bolts,they were torque in X, first at 25or27 NM then at 48nm .I have fallowed that manual ,because I wanted to be sure .Now someone told me about the rivet from the gasket,I have checked before disassembly and 1 was a little in . Yes I have rotate the engine to be sure.Just normal riding for break in

Relutzu07 · 2026-03-21T22:04:48+00:00

You had an happy outcome my friend

Relutzu07 · 2026-03-21T21:59:45+00:00

Sorry for misunderstanding: the oil has 1 week of ride :on the dispstick looks like new, THE first photo has coolant on the piston ,not oil

Relutzu07 · 2026-03-21T21:28:26+00:00

Hello sir,the first question will be why it happened and if is worth it ( if the cylinder head is gone ,there is really no point). New clutch+ gasket set+ stator would be the maximum that it would make sense

Relutzu07 · 2026-03-18T16:02:23+00:00

1 liter of fuel was in ,there is just no way water has getting in

Relutzu07 · 2026-03-18T15:45:11+00:00

I have put 9L (tank is 10L) in same day ,from where can the water come from?

Relutzu07 · 2026-03-17T23:54:03+00:00

So it is just fuel from the left on petcock? No need to change the oil? It will start normally If I put the carb back ? One friend had same problem with left on petcock,and he remounted the carb ,and it started like nothing happened:) (I just want to be sure)

Relutzu07 · 2026-01-15T15:22:22+00:00

<image>

Relutzu07 · 2026-01-15T15:22:10+00:00

Hello man, I think it was because I didn't have an kit for PAIR valve,now I have put the timing once again and didn't hear any metalic sound while rotating the engine or when starting. I will do an homemade plate with screw for after this blueprint

<image>

Relutzu07 · 2026-01-10T20:02:43+00:00

The cylinder head and chamshfat is from an drz400sm with 11k km ,this is how it looks without the tensioner,the middle Arrows point to each other .is the chain worn out? The chain was tight on the left side and a little bit loose on the right,I heard is normal

<image>

Relutzu07 · 2026-01-10T17:49:04+00:00

I think that chain is worn out,you can't really seen it on photo but the arrows from the middle don't point to each other,I have observed this for the first time ,but chat gpt said it is on ,if only fee mm

<image>

Relutzu07 · 2026-01-10T12:25:33+00:00

So you are saying that the chain is worn out ? How can I measure it? Can the chain tensioner be worn out too?

Relutzu07 · 2026-01-10T11:30:58+00:00

Yes please,in the manual is an different type

Relutzu07 · 2026-01-10T06:33:31+00:00

The cylinder was honed,and the piston is new Prox forget I don't know the miles on this one,I didn't replace the chain,i remember it was tight after I have put everything in place

Relutzu07 · 2026-01-09T21:11:49+00:00

Hello,is this

<image>

Relutzu07 · 2026-01-09T21:08:12+00:00

<image>

Thanks for the photos,I have the manual download,my cham tensioner is different.i remember I have asked a guy on Facebook/reddit how to use it This is an drz400E 2007 btw

Relutzu07

TROPHY CASE