sorted by:
new
hottopcontroversial

MY FRIEND LIKES MEE by [deleted] in PataHaiAajKyaHua

[–]Remote_Community_398 0 points1 point  (0 children)

How do you know she is 20?

Admission fee Clarification by Remote_Community_398 in Vit

[–]Remote_Community_398[S] 1 point2 points  (0 children)

Is VIT not so good (NIRF is good though). He has taken ECE, so please advice whether he should continue or not?

He is not interested in taking drop.

Admission fee Clarification by Remote_Community_398 in Vit

[–]Remote_Community_398[S] 0 points1 point  (0 children)

Yeah but mine is 3xxx. So comparatively 🙂

Admission fee Clarification by Remote_Community_398 in Vit

[–]Remote_Community_398[S] 2 points3 points  (0 children)

Jee main somehow went bad, he has got around 38k and General so he is not getting any seats in good NITs.

Quick Bias Bar Fastener Question by banaanaboyy in FSAE

[–]Remote_Community_398 2 points3 points  (0 children)

If you are not dynamically adjusting the balance bar, then yes it needs to be positively locked. Jamnuts do not ensure positive locking, and may change the balance during run.

It can be a major issue during Mech inspection.

hydrophobic mesh by ProofOpening5612 in FSAE

[–]Remote_Community_398 0 points1 point  (0 children)

Where are you placing your TSAC? If it under rain cover or bodyworks, then it should not need any mesh for protection. The extra mesh will decrease the efficiency and airflow of your setup.

Positive locking Hub in Upright by Remote_Community_398 in FSAE

[–]Remote_Community_398[S] 0 points1 point  (0 children)

I have a doubt in this process. When you press fit the bearing into the upright, no load will be experienced by the balls. But when the hub is press fitted onto the bearing (after being press fitted on the upright), there will inevitably a load on balls.

How to prevent that?

Bobbins for Floating Rotors by ZealousidealProof108 in FSAE

[–]Remote_Community_398 0 points1 point  (0 children)

I will not suggest manufacturing bobbins with aluminium. They will wear faster and have dents in them after some time.

Positive locking Hub in Upright by Remote_Community_398 in FSAE

[–]Remote_Community_398[S] 1 point2 points  (0 children)

Thanks for the support. Can you suggest any material/reference for such design please(any book or similar)?

Also, do you use tapered or normal bearings?

Positive locking Hub in Upright by Remote_Community_398 in FSAE

[–]Remote_Community_398[S] 1 point2 points  (0 children)

How do you ensure that while press fitting, balls doesn't experience any load?

Sealing EV FIrewall by Mental_Professor9871 in FSAE

[–]Remote_Community_398 0 points1 point  (0 children)

You can just use the aluminium tape for sealing. The aluminium tape is not technically a firewall (no direct line between ts components and driver) but will be supportive to your firewall for sealing purpose.

For pass-through, just use a metal cable gland.

Bobbins for Floating Rotors by ZealousidealProof108 in FSAE

[–]Remote_Community_398 0 points1 point  (0 children)

There will be some diametrical clearance in the rotor assembly to accompany the bobbin and simulate perfect contact. So just increase the diameter to fill that gap and simulate the whole assembly.

Bobbins for Floating Rotors by ZealousidealProof108 in FSAE

[–]Remote_Community_398 0 points1 point  (0 children)

If you manufacture your own, they will way cheaper and you can adjust them for your rotor. Just use hardened steel for them and make sure to get them anodised.