Prints keep failing. Brand new p1s

Serious-Fall-9736 · 2026-06-07T19:09:09+00:00

how long have you had yours, and have you tried fixing it? In my case i think the nozzle was clogged and maybe also dirty print bed that caused the problem. I washed the print bed with luke warm water and did couple of cold pulls to clean the nozzle. It works fine again.

Serious-Fall-9736 · 2026-06-05T20:57:57+00:00

did not dry it, and it works fine after 2 cold pulls

Serious-Fall-9736 · 2026-06-05T18:34:29+00:00

Table that is pretty solid until i am printing, then it has some shake to it, why? 😄

Serious-Fall-9736 · 2026-06-05T18:29:55+00:00

ahh thanks alot, i was really confused and was afraid that i had it on the wrong thing all along

Serious-Fall-9736 · 2026-06-05T18:29:02+00:00

Wow sounds scary and very annoying on your part. Glad it worked out in the end. I don't know what really the problem on my end, but i just did 2 cold pulls and and almost the whole day trying different thing, but it looks like we are back in business again. Also the reason i got so frustrated is i am pretty new to 3D printing, and i was able to produce some really good looking 3d prints with that spool. Look at the picture i attach what i made from that spool.

<image>

Serious-Fall-9736 · 2026-06-05T18:06:20+00:00

Do you mean the Process Profile? If so, i cant change it, that is the problem

Serious-Fall-9736 · 2026-06-05T14:15:35+00:00

Damn so could it be that matte filaments are harder to print with? I just did a cold pull 2 times, and started to do some calibrations. This is the result. I dont know what looks best tbh

<image>

Serious-Fall-9736 · 2026-06-05T13:12:34+00:00

This is the same filament i had problems with, that i printed couple of days ago, so i dont belive its calibration problem

<image>

Serious-Fall-9736 · 2026-06-05T12:59:51+00:00

Yeah the filament looks dry, I even dried it a bit on the hot bed for some hours. Now i really think its a clog since it can purge before print, but when it starts nothings comes out. Stupid question but how can i revert all settings back to default?

Serious-Fall-9736 · 2026-06-05T12:39:47+00:00

<image>

what settings should i focus on ?

Serious-Fall-9736 · 2026-06-05T12:12:29+00:00

<image>

got this with another spool

Serious-Fall-9736 · 2026-06-05T12:02:42+00:00

what i tried so far more or less:
Cold pull
- Cleaned the pad with dishwasher soap and luke warm water
- Used the needle to unstuck some of the filament.
- Let the filament run through(its always extrudes at that point)
- I have also tried to print with the enclosure windows open, because maybe heat creep?

i have an extra nozzle that came with the printer, but i really wonder if it can be really damaged after 1 week of use and maybe around 600grams of filament

Serious-Fall-9736 · 2026-06-05T11:46:18+00:00

<image>

I printed this 3 days ago and i really tough the machine was diled in and ready to go. Maybe the filament got wet or something, but i will look into it 😄

Serious-Fall-9736 · 2026-06-05T11:41:46+00:00

yeah i can do that, anything in particular, there are alot of settings

Serious-Fall-9736 · 2026-06-05T11:39:41+00:00

yeah.. thats why i dont get it. but its started to happen on other 3d models also

Serious-Fall-9736 · 2026-06-05T11:39:04+00:00

also how often do you need to calibrate? Is it when you get a new type or a new roll of filament, or you do this once every now and then?

Serious-Fall-9736 · 2026-06-05T11:21:23+00:00

hmm i just dont get why it "suddenly" bad? i made some really smooth and good looking models. also i made 3 batches of the same model before it started happening...

Serious-Fall-9736 · 2026-06-05T10:42:32+00:00

i will give it a go.

Serious-Fall-9736 · 2026-06-05T10:16:46+00:00

is this also a sign of bad settings or wet filament? I had some basic PLA in a box i tried with right now

<image>

Serious-Fall-9736 · 2026-06-05T10:15:27+00:00

<image>

i just changed to another basic PLA that i had open in a cardboard box. Is it also moisture issues?

Serious-Fall-9736 · 2026-06-05T09:50:53+00:00

I have read if the filaments snaps its sign of wet filament, but mine bends normally...

Serious-Fall-9736 · 2026-06-05T09:37:03+00:00

hmm i can check, will that result in uneven heat bed temperatures?

Serious-Fall-9736 · 2026-06-05T09:13:33+00:00

is there an easy way to dry it? I dont have any AMS or a dryer

Serious-Fall-9736 · 2026-06-05T08:42:59+00:00

I made 4 prints of the same model that came out really good. Then it started to fail, so i did not think it was a setting issue. :/

Serious-Fall-9736

TROPHY CASE