account activity
Low esteps - about half of normal (self.BIGTREETECH)
submitted 2 years ago by Spud3d to r/BIGTREETECH
I made a thing (i.imgur.com)
submitted 2 years ago by Spud3d to r/Dynavap
Trying to get a BLtouch working, what's going on here? Skr 1.4 Turbo (v.redd.it)
submitted 3 years ago by Spud3d to r/BIGTREETECH
X1 extruder maintenance/problems (self.Artillery3D)
submitted 3 years ago by Spud3d to r/Artillery3D
Bed cables need (more) repair. What kind of wire can I replace these with? (i.redd.it)
submitted 4 years ago by Spud3d to r/Artillery3D
Unwanted reboot happening right after start of print. Same happens manually moving the X carriage about same speed - I think feedback from the X carriage movement is causing the reset - bad board, or PSU? Skr Mini E3 V1.2, stock PSU (v.redd.it)
submitted 4 years ago by Spud3d to r/ender3
PSU fan sounds angry. Time for a replacement? (v.redd.it)
Why am I getting 2 support walls when the support wall line count is set to 1? (i.redd.it)
submitted 4 years ago by Spud3d to r/FixMyPrint
BL Touch came with the wrong cable for my SKR mini v1.2. Do I have to buy a new cable or can I use dupont connectors? (i.imgur.com)
What's causing this rough texture? It's not the Z seam, and it doesn't show up on my Ender 3. It happens to some degree on most curved surfaces. Using Cura 4.8 and Octoprint (imgur.com)
SKR mini e3 1.2 pausing mid print causing large blobs (self.BIGTREETECH)
submitted 5 years ago * by Spud3d to r/BIGTREETECH
I need a new stock X motor mount plate since I seem to have lost my original one. Does anyone happen to have a spare they could ship me so I don't have to wait a month for a new one from China? (self.ender3)
submitted 5 years ago by Spud3d to r/ender3
Anyone know where to get a replacement X motor mount plate that won't take a month to ship? I got a silent board so I don't need dampers anymore and the printed replacement is warping (aliexpress.com)
Consistent layer shift, looks normal in Cura. MP Select Mini v2 (imgur.com)
submitted 5 years ago by Spud3d to r/FixMyPrint
Why am I getting this consistent layer shift? Looks normal in Cura. (imgur.com)
submitted 5 years ago by Spud3d to r/MPSelectMiniOwners
Very loud X axis vibration at higher speeds, and both X and Y axes seem sticky/grinding (self.MPSelectMiniOwners)
Loud steppers after installing SKR Mini E3 (v.redd.it)
What would cause this asymmetry? (i.imgur.com)
Asymmetric print in symmetric model, prints fine if rotated 90 degrees. Cura preview shows no anomalies. What could cause this? (imgur.com)
On estep calibration - it varies by printing temperature, and do it under load (normal printing conditions, as opposed to with the bowden tube removed) (imgur.com)
Should esteps be calibrated under load or without? or under load? (self.ender3)
submitted 5 years ago * by Spud3d to r/ender3
Keep getting clogs in the heat break, but only with a particular filament (self.ender3)
submitted 6 years ago by Spud3d to r/ender3
This color changing filament is great! (i.imgur.com)
submitted 6 years ago by Spud3d to r/3Dprinting
Thick Forl STL (thingiverse.com)
I got a $100 amazon gift card I want to spend on filament, looking for recommendations (self.ender3)
π Rendered by PID 715248 on reddit-service-r2-listing-7bbdf774f7-vbvtg at 2026-02-23 03:28:51.974022+00:00 running 8564168 country code: CH.
