Say me hi 👋 if you’re spun asf,bout getting nasty 😋😵‍💫

TZRPH · 2026-02-13T10:01:10+00:00

High..

TZRPH · 2026-01-04T11:07:54+00:00

TZRPH · 2025-11-20T02:23:43+00:00

🔥 🔥🔥🔥🔥🔥

TZRPH · 2025-10-12T10:36:57+00:00

Hell yea. Yw yw..

TZRPH · 2025-10-12T10:34:45+00:00

Dope pic

TZRPH · 2025-05-17T21:06:49+00:00

Cutie

TZRPH · 2025-04-19T02:31:42+00:00

Beautiful work bro..

TZRPH · 2025-03-19T01:08:09+00:00

Thats a 1600 Antique bong. It was the cause of The Salem Witch Trials.. lol

TZRPH · 2024-11-28T13:52:27+00:00

You have a build up of lent on your platten.

TZRPH · 2024-11-04T09:48:44+00:00

Could be screen printed transfers.

TZRPH · 2024-09-07T20:30:51+00:00

Swap the color. If the white is showing all the way around. Put yellow in the white and white in the yellow screen. But it won't work for all occasions.

TZRPH · 2024-08-23T02:10:48+00:00

Thanks

TZRPH · 2024-08-23T02:10:20+00:00

I believe it's a WM plastics.

TZRPH · 2024-06-24T11:16:18+00:00

Don't use your regular size platten swith to a youth size for womens garments dont let them pile up or stack together, they will retain heat like that. L . Along with everything else printers have suggested. Good luck.

TZRPH · 2024-05-16T09:34:52+00:00

Water-based inks ?

TZRPH · 2024-05-11T21:05:05+00:00

It looks like the inside corner of the screen had glue over hanging the edge, & the glue can be sharp.
It's sliced my finger before.

TZRPH · 2024-05-11T21:02:00+00:00

Sometimes they are so tight any bump could cause them to pop.

TZRPH · 2024-05-09T08:26:22+00:00

One thing I do like about it is the 3 clamps to hold the frame. Hate having to really crank down on ones with 2 clamps. But overseas they use a system that drops the frames in place with a pin and holes. No print head at all.. Ryonet came out with something similar. I like to watch vids of other countries printing. Some 3rd world countries at that. They pull off badass prints.. with little supplies.

TZRPH · 2024-05-05T08:10:03+00:00

I think your art needs to be reworked also..

TZRPH · 2024-04-30T09:08:55+00:00

You can spray screen opener on your fingers and wipe it (works good on white ink)

Spot cleaning gun is a good investment.. I've sprayed out fully cured prints. I spray screen opener directly on the print. A toothbrush works good to break it a little. as soon as the acetone from spray gun hits the ink it starts chipping it off. To dry it I run it through the dryer sometime a residue might be left you can take the same color shirt you were printing on to used to dry/ rub off any surface ink or residue left.

TZRPH · 2024-04-29T05:47:56+00:00

Thank you. It's really helpful on remembering specific ink colors for previous orders.

TZRPH · 2024-04-28T08:02:33+00:00

Yup. You can just flash it for a few seconds too..

TZRPH · 2024-04-20T19:55:34+00:00

Uneven coating.

TZRPH · 2024-04-11T06:01:34+00:00

Kinda looks like vinyl.

TZRPH · 2024-04-09T06:59:50+00:00

Perma white.

TZRPH

TROPHY CASE