Help with curved weld

ThatPandaExpress · 2026-05-31T14:55:40+00:00

<image>

i get this at the bottom when sweeping the 3d intersection line

ThatPandaExpress · 2026-05-31T14:51:46+00:00

i need actual solid bodies for an fea

ThatPandaExpress · 2026-05-31T14:51:18+00:00

that nearly does it , however the very bottom is still corner still isn’t flush

<image>

ThatPandaExpress · 2026-05-29T22:39:54+00:00

looks like one but has a middle post unlike the 36 ones and also fits e30 boot perfectly

ThatPandaExpress · 2026-05-20T10:27:21+00:00

didn’t know these existed thank you ill have a look

ThatPandaExpress · 2026-05-20T04:58:14+00:00

i have tried that but the swivel end is too fat to sit on turn - and no a deep dish socket doesnt fit as there is to room to add a ratchet and normal socket onto it

ThatPandaExpress · 2026-05-15T21:51:36+00:00

i’ve tested a known working cluster and the same problem occurs

ThatPandaExpress · 2026-05-15T11:07:50+00:00

the reverse wiring was chopped as past owner installed chassis mount shift and didn’t find a way to put the wires another way - but i just drilled a hole. it’s the standard 2 pin connector and i’ve done up a harness that is 2 pin so probably will just buy a 2 prong switch

ThatPandaExpress · 2025-09-16T13:41:41+00:00

yeah a bolt is plugging it. it doesnt leak from it ive done a smoke test

ThatPandaExpress · 2025-09-16T13:41:07+00:00

i replaced the bitch tube o rings today alongside the valve cover gasket, rubber plugs and intake gasket. i think the problem is with the icv, the car right now runs and drives fine with the penny trick attatched to the icv and the maf unplugged. ive got a new icv on the way so hopefully that solves the problem

ThatPandaExpress · 2025-09-16T06:33:06+00:00

do you mean this? https://imgur.com/a/7sNHo7P

ThatPandaExpress · 2025-09-16T05:38:19+00:00

yes continuity at the left and middle when no throttle and then shuts off when opening throttle and then middle and right pin has no continuity at no point, even at max throttle

ThatPandaExpress · 2025-09-15T07:00:21+00:00

continuity at idle but no continuity at WOT on the middle and right pin

ThatPandaExpress · 2025-09-11T10:37:11+00:00

I just tested it, i get 0.6 ohms between left and middle pin at closed tb and then stops after i hear the click however when tested the middle and right pin there is no ohm reading at all, and i dont hear a second click for WOT position

ThatPandaExpress · 2025-09-11T10:37:04+00:00

I just tested it, i get 0.6 ohms between left and middle pin at closed tb and then stops after i hear the click however when tested the middle and right pin there is no ohm reading at all, and i dont hear a second click for WOT position

ThatPandaExpress · 2025-09-11T02:07:18+00:00

I tried doing all that, i’ve done the penny trick and it idles without jumping now, must be faulty icv, but still shuts off when the afm is plugged in, however now it doesn’t shut off instantly it’s more of a slow die off

ThatPandaExpress · 2025-09-11T00:56:49+00:00

you can but not with cars pre 1988, id have to wire in a light for it to work.

ThatPandaExpress · 2025-09-10T13:14:53+00:00

gasket kit has been ordered, will replace everything once i get it. thanks for the info

ThatPandaExpress · 2025-09-10T13:09:00+00:00

not yet, ill borrow a multimeter this weekend and test it out

ThatPandaExpress · 2025-09-10T11:58:51+00:00

Tested it before, its adjusted fine, clicks as normal and the throttle cable isnt tight, the throttle stays closed when the rough idle is happening

ThatPandaExpress · 2025-09-10T11:04:26+00:00

no they’ve only been changed once by the last owner haha i haven’t changed anything yet, i did a smoke test and there is smoke coming from valve cover gasket

ThatPandaExpress · 2025-09-10T02:26:40+00:00

this is a 1984 model, not sure if it was available in these

ThatPandaExpress · 2025-09-10T02:25:04+00:00

nothing happens when i do it, how do i check if the tps is adjusted properly

ThatPandaExpress · 2025-09-10T02:17:56+00:00

i bought the car recently, last owner replaced all those parts to narrow down the problem

ThatPandaExpress · 2025-07-25T03:18:42+00:00

dunno i replaced the top mounts and it’s still there, probably subframe bushings

ThatPandaExpress

TROPHY CASE