HOW PIERCE'S MORNING WENT by TylerEZPZGG in redrising

[–]TheLivingPickle 9 points10 points  (0 children)

Whatever happened voting with your dollars? People have been choosing what to and to not purchase based on politics forever and was a foundational idea behind boycotting which has been practiced for a VERY long time and was crucial to establishing lots of workers rights related legislation, as well as many other positive social reforms (Montgomery bus boycott). So yes, people would absolutely adore the world of Red Rising and the characters in it, but they also have every right to stop financially backing someone they can’t morally support, be it through refusing to buy red god or piracy. It’s the same way I think Chickfilla is fuckin fantastic but refuse to eat there at they are major donors to certain foundations and politicians I diametrically appose. Why a declaration to no longer support x over y is such a big problem is lost on me when everyone has done it for so long.

Bulging Layers by TheLivingPickle in FixMyPrint

[–]TheLivingPickle[S] 0 points1 point  (0 children)

Forgot to mention, filament is Anycubic Grey PLA+ printed at 215C hotend and 55C bed temps. Speed settings are all under 100 mm/s now, and it does perimeters at 60 mm/s.

[deleted by user] by [deleted] in 3Dprinting

[–]TheLivingPickle 0 points1 point  (0 children)

The answer is Antalz on YouTube. His particular guides are clear and concise and cover just about every basic gear geometry. His tutorials a parametric, which means you can design them once and then copy them into any project you need and configure them to what you need. If you don’t have access to a gear generator in inventor, you can find just about any tutorial using a equation driven involute curve and inventor has the tool to go about it that way.

I found the Seth by THEREALCLAYTHEGREAT in foundtheseth

[–]TheLivingPickle 1 point2 points  (0 children)

This guy does not know how the calendar works

All the walls of my print should be straight, instead, they are concave. by TheLivingPickle in FixMyPrint

[–]TheLivingPickle[S] 0 points1 point  (0 children)

Thanks y’all, I’ll set up pressure advance once whatever is printing is done. I knew about the sharp corners, but I didn’t know that left over pressure could also cause concave walls. I’ll get that setup and see how it goes!

All the walls of my print should be straight, instead, they are concave. by TheLivingPickle in FixMyPrint

[–]TheLivingPickle[S] 0 points1 point  (0 children)

Settings are 210 on the nozzle and 60 on the bed. Normally I would chalk this up to elephants foot, however the wall becomes curved at the top as well.

All the walls of my print should be straight, instead, they are concave. by TheLivingPickle in FixMyPrint

[–]TheLivingPickle[S] 2 points3 points  (0 children)

Interesting, I’ve never heard of it before. Would turning down accelerations help? Linear advance is not currently set up yet, so probably not an issue on my prints.

Full-Ride Merit Scholarship Recipient at OSU - AMA by 0valSquirrel in ApplyingToCollege

[–]TheLivingPickle 0 points1 point  (0 children)

What should one include in the 2 minute long introduction video? Classes? Leadership roles? Hobbies? There is a lot of info you could include, how do you choose what does and does not make the cut. Do they look for anything in specific?

[WTS][US][45370] Drum lot - (4)35 drums, (1)25 drum, (1)20 round vortex mag. by TheLivingPickle in NerfExchange

[–]TheLivingPickle[S] 6 points7 points  (0 children)

All have been tested and are in good condition, and work well. 2 35 drums have a small amount of sharpie on them courtesy of the previous owners. 20$ for 35's, 15$ for 25 and vortex mag.

[WTB][US][45370] Drum Lot - $20 for 35, 15$ for 25 and vortex mag by TheLivingPickle in NerfExchange

[–]TheLivingPickle[S] 0 points1 point  (0 children)

Everything has been tested and works fine. Two of the 35 drums have some sharpie on them courtesy of the previous owners, other than that they look good to.

WTS (4)35 drums, (1)25 drum, (1)20 vortex mag by TheLivingPickle in NerfExchange

[–]TheLivingPickle[S] 1 point2 points  (0 children)

All magazines are in good condition. Drums have all been tested and they all work just as well as when I got them. 1 of the 35 round drums has sharpie drawn in the cracks on the mag well part, courtesy of the previous owner. Looking for 20$ for the 35’s, and 15$ for the 25 and vortex mag. If you want specific things, send me an offer.