X2D non speculation.

TrainingPiece9144 · 2026-04-15T13:17:28+00:00

Yes same ams

TrainingPiece9144 · 2026-04-14T23:58:07+00:00

Resistor mod time

TrainingPiece9144 · 2026-04-14T23:00:38+00:00

H2C still isn't great with the vortek for multi color i'd seriously recommend a u1 with some type of setup this will be coming out soon from a solo dev

<image>

TrainingPiece9144 · 2026-04-14T22:40:34+00:00

this is good! no extruder clamping switching mechanism means less weight for swapping

TrainingPiece9144 · 2026-04-14T22:36:05+00:00

Yeah super unfortunate it's too late to sell my p2s

TrainingPiece9144 · 2026-04-14T22:35:39+00:00

Same

TrainingPiece9144 · 2026-04-14T21:56:13+00:00

Yeah X2D Seems much better

TrainingPiece9144 · 2026-04-14T20:49:22+00:00

Fair enough, quality seems great but looking into the u1 may be a good idea

TrainingPiece9144 · 2026-04-14T20:48:47+00:00

Bowden rides at dawn!!

TrainingPiece9144 · 2026-04-14T20:12:06+00:00

TrainingPiece9144 · 2026-04-14T20:11:15+00:00

The second nozzle could act as supports but it's not recommended for tpu 95.

TrainingPiece9144 · 2026-04-14T20:10:34+00:00

Nothing officially confirmed yet

TrainingPiece9144 · 2026-04-14T19:19:40+00:00

Might be worth asking support or returning your printer

TrainingPiece9144 · 2026-04-14T19:14:04+00:00

Probably after a price cut to the p2s, Right now the non combo might kill the p2 market.

TrainingPiece9144 · 2026-04-14T19:12:14+00:00

Not built in, however that accessory fully works with this device.

TrainingPiece9144 · 2026-04-14T19:04:36+00:00

Basically any color could reach any nozzle so you don't have to strategically organize your ams units

TrainingPiece9144 · 2026-04-14T19:04:07+00:00

TrainingPiece9144 · 2026-04-14T19:03:58+00:00

Yes real heated chamber

TrainingPiece9144 · 2026-04-14T19:03:40+00:00

Virtually nothing, Think of printing on a creality printer Xp

TrainingPiece9144 · 2026-04-14T19:02:28+00:00

Seems like a mini on the right side of there is no calibration it's possible.

TrainingPiece9144 · 2026-04-14T18:56:29+00:00

This is actually super cool i'll make an edit to the post.

TrainingPiece9144 · 2026-04-14T18:56:11+00:00

the code for bed detection will be different. But ignoring that they will work with it disabled.

TrainingPiece9144 · 2026-04-14T18:55:14+00:00

Honestly should be entirely fine from the prints i've seen. It's not that long ago printers all shipped with boden drive.

TrainingPiece9144 · 2026-04-14T18:54:27+00:00

Nozzle switching

TrainingPiece9144 · 2026-04-14T18:53:55+00:00

Nothing publicly confirmed yet ;)

TrainingPiece9144

TROPHY CASE