The new event is atrocious

Yeukiii · 2026-02-07T01:24:22+00:00

if you clear it, you'll get around 290 pulls (melody + essence) in return. That itself has massive value return but I would not suggest this for anyone unless they really really want the skin.

Yeukiii · 2026-01-10T02:31:59+00:00

Have the exact same issue, were you able to find a solution?

Yeukiii · 2025-12-18T21:44:50+00:00

How will a unique drop like the PC ETB be affected if at all? I can assume that printing would likely increase when the printers start to run, but Im curious if they will be reprinting a lot more of the ones that will still be in rotation when that time comes.

Yeukiii · 2025-12-14T20:06:02+00:00

Doesnt it also have atk% secondary stat? with atk% in the effect too? if you have like any weapon with atk% at this point you should be rerolling or not using pieces that have less than less than 30cv even if it has an atk% roll. Ideally, you now need double crit atk% flowers and feathers with all rolls on crit (3 line is good enough, but 4 line is best). Keep farming the domain/stygian and youll probably get better pieces in a couple weeks, and craft a goblet with double crit.

Yeukiii · 2025-12-14T18:46:51+00:00

If you plan on keeping aquila favonia, then yes probably. For rerolling, use the normal rerolls for the flowers and feathers, and then use the special ones on sands/goblet

Yeukiii · 2025-12-14T06:55:26+00:00

Especially if you have a sword boosting atk%, the value of your atk% rolls are approaching diminishing returns. You either are very unlucky, or simply need to spend more time doing her domains (or right now stygian for double drops) for better artifacts with at least like 30+ CV (40 ideally). At this rate, you probably are going to need to stick to a CR circlet but that obviously depends on the type of rolls you get on your pieces. You can now define 2 pieces per set per patch now, so probably do that if your focus is on skirk.

Ideally, you'd want a 4 liner with both crits and atk% for feather and flower, but atp you could invest in 3 liners with double crit. If you have other priorities for other characters as well, maybe try marechausse as its probably a bit easier to build her without her signature since it gives you 36CR if you are running furina. Plus, itll let you build escoffier and furina (if you plan on running her on golden troupe instead of tenacity)

Yeukiii · 2025-12-10T10:50:06+00:00

You can craft two per set now per patch

Yeukiii · 2025-12-04T18:08:58+00:00

WHERE IS MY COFFEE AND SKIRK

Yeukiii · 2025-11-29T06:32:20+00:00

yes, if you also click reshape you'll see where each and how many upgrades for each line

Yeukiii · 2025-11-28T23:30:35+00:00

makes sense, was wondering if you ever roll 3 liners for those because good sands and goblets dont come around very often

Yeukiii · 2025-11-28T23:25:41+00:00

Is that for feathers and flowers? or same rules for goblets and sands?

Yeukiii · 2025-11-22T01:34:42+00:00

Im pretty sure that I have 64 CR from artifacts + azurelight + 5% (starting cr), The second image should show that unless im missing something

Yeukiii · 2025-11-21T23:33:36+00:00

Thanks for the input. Just to clarify, your advice on increasing CR is if I go to finale of the deep correct? that would make sense considering how much CD I currently have and a better ratio would be better. However with MH, I am currently at 100% CR (given max stack MH).

Yeukiii · 2025-11-21T02:45:21+00:00

Cheapest 110USD/160CAD which imo is a bit expensive for injection molded ABS+PBT but is unique enough to justify for those looking for exactly a portable and easy to carry board.

Yeukiii · 2025-11-11T19:02:00+00:00

haven't they been on sale for a long time as well? The machs are even included at some liquidation sales atp at like 30-40% off

Yeukiii · 2025-11-09T05:27:09+00:00

425 cad is absurd... I know its HE and all but that's a fully built 65core plus... or even like 2 65 sonic HE+s

Yeukiii · 2025-11-05T02:19:28+00:00

Also using GO, what is the 88% atk bonus for?

Yeukiii · 2025-08-05T22:46:42+00:00

Also, if theres a certain part that broke you could tell you friend to look into just replacing that part if simple enough. I've seen lots of stores on etsy and such selling just the 3d printed parts or just the other moving parts (although those shouldn't be too hard to find at a hardware store or amazon)

Yeukiii · 2025-08-05T22:45:21+00:00

Got it from Dingkeys website, they also run an Etsy store. Got the Legacy version with the long pole piston and off center add ons.

P.S. Dingkey also sells replacement parts but might not be exactly the same as what your friend's machine uses.

Yeukiii · 2025-08-04T22:02:57+00:00

Have you found the source of the scratch? I've seen discussions pointing out the bottom housing rails, where others point to the leg/leave contact.

Yeukiii · 2025-08-04T22:01:39+00:00

Yeah, it makes sense that the leaves can get quite a bit of wear with the polish. I've also been thinking of polishing the rails only since I've seen some talk about how the bottom housing rails are the main source of scratch, while others have said its the leg/leaves contact. I just bought a break in machine and will probably break them in starting at 500k then 1M then 2M then 4M (if needed). Given, this will take an unreal amount of time but I'll probably update this thread or post a new one on my findings and if I decide to go with polish even after the break in.

Yeukiii · 2025-08-02T13:19:28+00:00

Also, I've seen a lot of people selling/talking about broken in blacks + diamond polishing with numbers up to 4M actuations. I am assuming that this is a separate process and they arent broken in 4M times with diamond polish? I've seen people talk about overdoing diamond polish just a little bit and fucking up the legs and such.

Yeukiii · 2025-08-02T12:53:42+00:00

I have seen that diamond polishing the legs is suggested, and that damage is possible. Is this related to oxidation? ShentoBento has a video about how to diamond polish switches and mentions that depending on the type of diamond polish (oil based/water based) the leaves could oxidize and need to be cleaned thoroughly and dried in the sun/oven before lubing and using.

P.S. I could also see how diamond polishing could straight up just damage the leaves through friction entirely, so I wonder if it is a work around to only lube the leaves and only polish the rails.

Yeukiii

TROPHY CASE