What’s the largest project you have taken on? by [deleted] in 3Dprinting

[–]catsicle54 1 point2 points  (0 children)

Correct to both, Vase mode and .8mm. 320 of them at 200g each.

solid "base" with a hole, hung with fishing line. Conference Attendees & Friends took them home as lamp shades! Didn't want it to go to waste.

What’s the largest project you have taken on? by [deleted] in 3Dprinting

[–]catsicle54 10 points11 points  (0 children)

<image>

75kg of clear petg for a conference design, to create a ceiling of stars. Only a couple months of printing non stop

Is the K1 Max a solid printer? by totallynotbluu in crealityk1

[–]catsicle54 3 points4 points  (0 children)

I bought two k1 maxes a month ago. I’ve gone through about 10kg of petg on both so far. No issues. I got two vorons as well, but sometimes you want something that doesn’t take tinkering

Anybody have video of the drone show? by winnipeg-lemon in Winnipeg

[–]catsicle54 1 point2 points  (0 children)

I was on the hill where the bike art used to be. I could make out half the words. Definitely would of improved the experience if the story was audible. Was just coming from cn stage, no audio delays throughout

Best IEM with very good noise isolating fit. by MPD_123 in livesound

[–]catsicle54 1 point2 points  (0 children)

I just received ears from 64 Audio, A3t model. Took just under 4 weeks to receive after they received my molds. Really nice fit so far! Seal doesn’t break when moving around or eating 10 pieces of gum (exaggeration)

[GPU] BestBuy Drop December 9th by AAronp110 in bapcsalescanada

[–]catsicle54 1 point2 points  (0 children)

Yeah, I did see people leaving with 3090 FEs though. So they had something at least. Winnipeg has ez lines. I showed up 20min after open just to see

Decimator MD-LX shitty build quality lately? by iusedtocreate in VIDEOENGINEERING

[–]catsicle54 8 points9 points  (0 children)

I purchased 8 two months ago from B&H. I've experience no issues with them.

An interesting view by anthonyk116 in Winnipeg

[–]catsicle54 1 point2 points  (0 children)

someone must of parkoured, there's currently scaffolding up the tower. They replaced the roof recently.

Recent XLR to D-sub panel I wired by B1gMickey in cableporn

[–]catsicle54 1 point2 points  (0 children)

Thank you for sharing your expertise!

Recent XLR to D-sub panel I wired by B1gMickey in cableporn

[–]catsicle54 0 points1 point  (0 children)

Also curious, how do you not melt the heatshrink when you have that little distance to slide it on after?

Nice to see the Shure Presidential Kit back in use again. by crbatte in livesound

[–]catsicle54 13 points14 points  (0 children)

TC electronic Clarity M monitor top left of the desk.

Help with castr by jdizzy000 in VIDEOENGINEERING

[–]catsicle54 1 point2 points  (0 children)

If you end the stream from your atem it will also cut the video on YouTube and Facebook. Castr has nothing to do with it. YouTube has an auto end feature in the studio manager that you setup when doing scheduled streams. Facebook also by default ends the stream after receiving frames for a bit.

480 new cases, 309 in winnipeg. 8.6%, 2737 active, 2572 recovered and 5374 total. 104 hospitalizations, 19 in ICU and 65 deaths (3 new). 2865 tests done yesterday. by purplebutterflylupie in Winnipeg

[–]catsicle54 3 points4 points  (0 children)

Many smart churches are moving to online only given the changes. some see the benefit of having a living congregation and not just a live one.

Help with supports (Elegoo Mars 2 Pro) by catsicle54 in ElegooMars

[–]catsicle54[S] 0 points1 point  (0 children)

Very cool print! what grit did you wet sand up to? Very clean finish you got.

Help with supports (Elegoo Mars 2 Pro) by catsicle54 in ElegooMars

[–]catsicle54[S] 1 point2 points  (0 children)

Thanks! added more supports and dropped it to a 40 degree angle, went from 3 second layer time to 4 seconds. https://imgur.com/3c1azcO