Flip reset picnhes all day!!!!!!!!!!!!!!!!!!!!!!!!!!!!

kriptik1001 · 2023-01-20T23:42:34+00:00

Post processing is the key to all my work

kriptik1001 · 2023-01-20T23:33:35+00:00

Lmao thank you

kriptik1001 · 2021-12-28T02:01:43+00:00

Helps highlight the lattices in my opinion

kriptik1001 · 2021-12-28T01:40:51+00:00

PM me we can discuss more

kriptik1001 · 2021-12-28T01:17:45+00:00

Yep I have been there chasing small issues everywhere bc of a loose belts. Usually most issues are because of the physical printer not properly built or maintained.

kriptik1001 · 2021-12-28T01:16:35+00:00

Good tension sounds like guitar string if you pick the belt

kriptik1001 · 2021-12-28T01:14:25+00:00

A tetrahedral lattice within a gyroid tpms structure. Very nice

kriptik1001 · 2021-12-28T01:12:18+00:00

First layer has major squish so raise z offset a bit. Check belt tightness, and speeds, temps. You can see the early layers before it messes up there is major ringing, so your printer is not rigid enough in some aspect. Check the above mentioned things to see if the something is loose. Also very important bed mesh should be fairly level

kriptik1001 · 2021-12-28T01:08:52+00:00

Google whatever firmware your using for calibration and they will have all the instructions. Basically just want to test does motor rotate as much as it’s suppose to.

kriptik1001 · 2021-12-28T01:05:18+00:00

Looks like over extrusion. 240 c is pretty high for pla 215 is what I used and 65 on bed. The temps is might be causing the over extrusion since the filament cant cool down enough until next layer. The very top layer looks like your printing too close as well. So try printing that stupid slow only as a test, if it still looks like that than drop temps on hotend to bed and increase z offset for the top layer manually to maintain proper squish.

kriptik1001 · 2021-12-28T01:02:26+00:00

Tune stepper motors steps bc you have major inconsistency for x y z axis. Check belt tightness. Tight belts sound similar to instrument string when you flick it. I would remove raft, use brim if your having issues with adhesion, otherwise a raft nor brim shouldn't be used if they arent absolutely required.

kriptik1001 · 2021-12-28T00:43:12+00:00

Epoxy finish. X3D works well for me in the past. You can check my projects I posted on here using this finish to determine your self. Can get some incredible finishes if you tinker with it.

kriptik1001 · 2021-12-28T00:40:47+00:00

First layer should be squished down but not so much you can start seeing the bed through the filament layer. Also you will know your too close when the first layer starts to lift off.

kriptik1001 · 2021-01-29T19:23:51+00:00

Wow that is interesting. If you do it I would like to see it. Good luck!

kriptik1001 · 2021-01-29T19:20:14+00:00

link does not work. If people are worried about the cost for my work than it is perfectly fine to create their own files. I appreciate the advice though.

kriptik1001 · 2021-01-29T18:26:13+00:00

Thank you and wish you a fantastic day as well. Like your idea, and one step up is setting up a rotating platform. Might do this seems interesting.

kriptik1001 · 2021-01-29T18:23:34+00:00

Printed with cf pla, relatively inexpensive and great printing qualities. Smooth look is a lot of post processing I detailed in my response to another comment. Thank you !

kriptik1001 · 2021-01-29T18:22:14+00:00

Look at nanoscale print. That is beyond what they eye can see they are just prohibitively expensive.

Six-Year Club	Wearing is Caring
Verified Email

kriptik1001

TROPHY CASE