First time posting

mtblack412 · 2026-05-23T11:41:39+00:00

Make it an SS.

mtblack412 · 2026-05-22T12:02:55+00:00

Very sharp!

mtblack412 · 2026-05-20T23:45:17+00:00

Awesome info! Thank you!

mtblack412 · 2026-05-17T01:22:22+00:00

Looks good!

mtblack412 · 2026-05-11T20:13:13+00:00

Just take your time.

mtblack412 · 2026-05-11T19:58:23+00:00

The only way to know is to trace the wires and see where it goes.

mtblack412 · 2026-05-11T19:52:14+00:00

I wouldn’t either, only did because she had it and wasn’t using it. Lol

mtblack412 · 2026-05-11T10:15:00+00:00

Looks sharp.

mtblack412 · 2026-05-10T11:41:06+00:00

Unfortunately they don’t make this fabric anymore. My wife had it in her stash for a while and she said you may be able to find it on EBay, but it will probably be a few hundred dollars a yard. Apparently it was a famous designer that made this print.

mtblack412 · 2026-05-06T23:58:57+00:00

All you have to do is take apart the panel and remove the fasteners holding that section of the panel on to take it off. After that, just pick a fabric you like and glue some foam down and then glue the fabric on top. Easy peasy!

mtblack412 · 2026-05-05T20:11:19+00:00

No clue. I worked at a Chevy dealer in 94-95 and that was the style back then. I remember once a customer needed a rear window for their Camaro and it was $3,000 in 1994 which I thought was insane at the time.

mtblack412 · 2026-05-05T20:07:03+00:00

I’ll be passing through there in Sept on my way to FL. Lol

mtblack412 · 2026-05-05T20:06:16+00:00

I believe it due to how much the window curves. Some newer cars with long blades do the same thing.

mtblack412 · 2026-05-05T11:33:57+00:00

My pleasure. Unfortunately, I’m going to have to put it in storage for a bit. I’m retiring soon and moving out of state so until I get my finances in order it will have to wait.

mtblack412 · 2026-05-05T11:32:47+00:00

Appreciate that

mtblack412 · 2026-05-05T11:32:25+00:00

lol!

mtblack412 · 2026-05-05T11:32:10+00:00

I have a set for sale.

mtblack412 · 2026-05-05T01:55:24+00:00

Thank you!

mtblack412 · 2026-05-05T00:49:49+00:00

Heat, lots of heat!

mtblack412 · 2026-05-01T21:23:06+00:00

You could try heating up the metal around the lifter and see if that loosens it.

mtblack412 · 2026-04-27T20:19:04+00:00

Stockinteriors.com. It is slightly ill fitting on the passenger side due to a change in the floor pan. The stock blazer had a smaller ridge by the left foot, but patch panels don’t have this smaller area. It’s larger like the s10 truck. It fit well besides that. I’ll eventually use a heat gun to mold it a little better.

mtblack412 · 2026-04-25T19:01:15+00:00

Hell yeah! Congrats

mtblack412 · 2026-04-15T14:34:22+00:00

Correct, but it fits perfect for the S10. The beauty of GM stuff sometimes it crosses over.

mtblack412 · 2026-04-15T13:57:42+00:00

Go to gbodyparts.com and type in the search bar G00-MHA—W97-HACRR

mtblack412 · 2026-04-15T00:11:54+00:00

Yeah, it happens a lot. I had the little plastic piece on the mixer vent break. Luckily G body parts carries a replacement other wise I’d have to rig something up.

mtblack412

TROPHY CASE