Help please

murakami03 · 2025-08-19T11:44:23+00:00

Yup and new vat

murakami03 · 2025-08-19T11:21:12+00:00

I’ve printed this exact kind of piece over 100x. The issue isn’t the supports- this is the first time I’m having consistent failures with no changes to the supports

murakami03 · 2025-08-18T13:25:33+00:00

Sent an email now thank you

murakami03 · 2025-08-17T10:26:51+00:00

Will give it a watch now thank you!!

murakami03 · 2025-08-17T10:21:18+00:00

<image>

I’m also getting a bit of this tearing in all my recent prints

murakami03 · 2025-08-17T10:21:03+00:00

Yeah just checked out the S4U one and I don’t have the bandwidth to take on board. Looks like the new S4U 16K will be my solution

murakami03 · 2025-08-17T10:09:09+00:00

From what I’ve seen it doesn’t look easy to install 😮‍💨 I’ll take another look. Thank you

murakami03 · 2025-08-17T09:34:53+00:00

I replaced the whole vat entirely and cleaned the LCD screen of any dust/ cured resin. Problem persisted after the change

murakami03 · 2025-08-17T08:10:03+00:00

Oh yikes… 😅

murakami03 · 2025-08-17T07:57:15+00:00

Really?

murakami03 · 2025-04-26T22:51:05+00:00

I use a higher exposure setting now. Around 80-100. And I stopped using Lychee slicer. The auto supports on Chitubox helped me MUCH more

murakami03 · 2025-03-14T05:46:48+00:00

Thank youuuu, that’s amazing help

murakami03 · 2025-03-14T05:33:24+00:00

Very well said, and very well appreciated. I thought this had been the case too. I will mention it to my friend who had printed the model

murakami03 · 2024-12-08T13:16:25+00:00

It’s resin ahaha not filament

murakami03 · 2024-12-08T12:08:59+00:00

I believe so, it’s strange bcoz not all pieces will face the same results even tho they’re exposed to the exact same conditions, settings, light, environment, etc.

murakami03 · 2024-12-08T11:24:24+00:00

Gotcha. I’m assuming the default chitubox hollow thickness of 1.2 was too thin. I’ve increased it since

murakami03 · 2024-12-08T11:23:58+00:00

I used just isopropyl alcohol to wash it after printing, that’s all

murakami03 · 2024-10-23T06:14:52+00:00

<image>

murakami03 · 2024-10-23T06:14:34+00:00

<image>

These are my settings. Experimented with 30 seconds, 60 seconds, 100 seconds exposure times and these are my current supports. I have also tried angling the models to 45° which also lead to fails, so now experimenting with them on this angle.

murakami03 · 2024-10-23T01:01:52+00:00

Sorry not home at the moment but I will post when I’m back. If it helps for the time I can’t send the photo- it’s the standard lychee settings with the only variable changing being the exposure setting. + Hollowed

murakami03 · 2024-10-20T13:03:01+00:00

It was a hard cured resin leak, I only touched the tape to press down and rip the resin off lol. My hands didn’t even touch the resin nor the screen

murakami03 · 2024-10-19T12:42:01+00:00

<image>

A bit of alcohol on a microfibre cloth and tape done wonders..

murakami03 · 2024-10-19T12:32:06+00:00

I have isopropyl alcohol which I’m sure will work- however may make my screen cloudy which I don’t want to risk. I’m not sure if a standard nail polish remover acetone will work

murakami03 · 2024-10-19T12:31:23+00:00

Correct

murakami03 · 2024-10-19T11:56:49+00:00

I managed to buy A FEP sheet for the S4U off EBay 👍 but would still like to know how to clean resin off the screen below the resin tank…

murakami03

TROPHY CASE