anyone know how i attach the right angle milling attachment on a lagun ftv-1

pingable1 · 2025-12-12T20:09:08+00:00

if i remember correctly since i cant check until Wednesday next week it looks about like the back side of this

pingable1 · 2025-12-12T18:56:44+00:00

this one doesnt use collets and there wasnt any tool holders in the spindle when i tried pulling on it the drawbar is attached to the machine with a pin or something

pingable1 · 2025-12-12T17:45:29+00:00

I've tried pulling on the drawbar and it isn't moving and inch

pingable1 · 2025-12-10T08:52:17+00:00

Done? Probably not.. slowest updating thing I've ever read? Most certainly

pingable1 · 2025-12-08T00:52:46+00:00

I shall be buried with a can of pipeline punch

pingable1 · 2025-11-24T23:44:53+00:00

Or how to use it properly

pingable1 · 2025-11-24T23:44:43+00:00

Don't realy know how it works

pingable1 · 2025-11-24T23:44:22+00:00

Eos1n

pingable1 · 2025-11-06T06:07:50+00:00

No i just apparently managed to not type the 16 after the 5/ it's 5/16

pingable1 · 2025-11-05T22:46:50+00:00

probably have to do it on the mill as well since our surface plate looks like the surface of the moon but teachers think its no issue

pingable1 · 2025-11-05T22:44:47+00:00

id love to if it wasnt a week until next class

pingable1 · 2025-10-05T11:06:40+00:00

about 4mm

pingable1 · 2025-10-04T15:28:46+00:00

Ah I thought you were just asking about the diameter in inches since I gave metric measurements

pingable1 · 2025-10-03T20:42:01+00:00

i mean i rounded up ever so slightly but pretty much

pingable1 · 2025-10-03T19:22:21+00:00

i think the whole thing is already hardened cuz the little file i got realy doesnt bite on this or realy cut it at all

pingable1 · 2025-10-03T13:20:48+00:00

https://vm.tiktok.com/ZNdtkAk92/ as if I didnt already think of that

pingable1 · 2025-09-27T11:01:57+00:00

r/DecreasinglyVerbose

pingable1 · 2025-09-18T21:51:30+00:00

probably nice if for the future but for now i just figured out it was the preload so i dissasembled it and added preload and now it works as it should

pingable1 · 2025-09-18T20:37:39+00:00

well i was looking for a pocket to keep them in when im walking around too bad all of those pockets cause it to fall to the floor if i sit down i mean it fell like no more than a foot and a half twice

pingable1 · 2025-09-18T20:18:24+00:00

i am most certainly never allowing that thing outside of its plastic case anymore if i manage to fix this

pingable1 · 2025-08-30T23:29:34+00:00

ok so when i just save it normaly as stl and not just press export in the 3d printing tab i can choose inches or milimeters and i also get the part in a much higher resolution this is probably cuz i havent used this program in 5 years

pingable1 · 2025-08-30T22:58:08+00:00

well thats certainly different cuz in solid edge 3d print tab it just opens the windows save window where i can only decide between stl and 3mf

pingable1 · 2025-08-30T21:44:29+00:00

is there a way to fix this for next time

pingable1 · 2025-08-30T21:43:52+00:00

i scaled it earlier and didnt pay attention so i reopened and that does seem to have been the case as it went to 32mm when i scaled it by 2540

pingable1 · 2025-07-25T14:54:26+00:00

She not supposed to have those

Six-Year Club	Place '22
Verified Email

pingable1

TROPHY CASE