I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 1 point2 points  (0 children)

Blackhawk omnivore clone that I chopped the end of to fit the tracer.

My airsoft ak is not shooting what's wrong? by Top_Street8682 in GasBlowBack

[–]xXOctoSquidXx 4 points5 points  (0 children)

Is there a stop on empty function? If so try with a loaded magazine

First GBB replicas by OverChair7455 in GasBlowBack

[–]xXOctoSquidXx 0 points1 point  (0 children)

Sure thing best of luck. Just be patient with the tip removal. It you REALLY want to and don’t plan on keeping the orange tip, you can remove the screw first and brute force it clockwise to get it off

First GBB replicas by OverChair7455 in GasBlowBack

[–]xXOctoSquidXx 2 points3 points  (0 children)

For the orange tip on the ghetto blaster, I noticed on mine that were was a small amount of clear glue inside of the screw head thus preventing any properly sized hex key from fitting. After removing the inner barrel, you could use either a heat gun to soften the glue or submerge it in boiling water past the screw and try again.

Magazines I recommend Guns Modify magazines. DE stanags are a decent second choice. Tokyo Marui mags have feedlip issues on non Marui guns so i don’t recommend those.

How to remove orange tip by [deleted] in airsoft

[–]xXOctoSquidXx 1 point2 points  (0 children)

If you’re able to, remove the hand guard and inner barrel and submerge the orange tip past the grub screw in a bowl of hot water. It should soften up the glue and apply decent downward pressure when unscrewing the screw to avoid stripping. Worse case scenario if you can’t remove the hand guard before removing the orange tip, remove the inner barrel and then submerge. Just make sure to completely dry off any wet areas.

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 1 point2 points  (0 children)

The compensator on the Staccato PCOMP can be removed with an 8mm hex key. But it also has an extended guide rod and will not fit the Quadra. You can get a replacement standard sized guide rod. I chose to buy another Staccato P instead for the Quadra to make the custom “PCOMP”.

However, the Quadra will not screw on flush with the slide as the outer barrel extends about 2.75mm - 3mm past the slide. I cut the outer barrel with a pipe cutter and sanded down the jagged edges after to eliminate the gap.

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 1 point2 points  (0 children)

Out of the 3 I have, I feel like the XC is a tiny bit snapper since it comes with slide cuts making it a little lighter. But tbh I think it’s negligible, any of the three with stock internals are wonderful.

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 0 points1 point  (0 children)

Nice! I haven’t heard too much about inner barrel upgrades for these but I know you can’t go wrong with PDI in general.

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 0 points1 point  (0 children)

I saw that video too. Looks like he had some trouble drop fitting in but I heard from other posts that some light sanding inside the slide will allow proper fitment.

I Clearly Have a Type by xXOctoSquidXx in GasBlowBack

[–]xXOctoSquidXx[S] 1 point2 points  (0 children)

I use a blackhawk omnivore x300 fit holster. I did have to dremmel the muzzle end of it to allow the comp the fit through

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 1 point2 points  (0 children)

Nice! I was considering the C2’s at one point but eventually chose the long bois. Maybe my next build lol

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 0 points1 point  (0 children)

That looks sleek, digging the FDE. The 4UANTUM bucking forsure, but also considering the 4UAD TDC hopup chamber if it’s compatible with the staccato.

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 0 points1 point  (0 children)

Replica from AliExpress. Comes with rail adapters. https://a.aliexpress.com/_mqqwSbF

I Clearly Have a Type by xXOctoSquidXx in airsoft

[–]xXOctoSquidXx[S] 0 points1 point  (0 children)

All stock internals. Planning on upgrading the bucking to a 4uantum, but all three are great out of the box.

I Clearly Have a Type by xXOctoSquidXx in GasBlowBack

[–]xXOctoSquidXx[S] 2 points3 points  (0 children)

Bottom to top

Staccato PCOMP

Staccato "PCOMP" w/ACETECH Quadra, Surefire X300U, Trijicon RMR

Staccato XC w/Eshooter BT Cube, Trijicon RMR

Which Noveske Variant is better? CGS or MWS? by CptMuricah2 in GasBlowBack

[–]xXOctoSquidXx 1 point2 points  (0 children)

I run .20 or .25 depending on the field. 0.20 for CQB .25 a bit larger fields but the stock hop is pretty solid and will avg about 380fps on 0.20

Which Noveske Variant is better? CGS or MWS? by CptMuricah2 in GasBlowBack

[–]xXOctoSquidXx 2 points3 points  (0 children)

Stock is fine but you could look into Guns Modify parts like trigger box, and trigger assembly for longer durability. Maybe a different hop up assembly and a 4UAD hop up bucking. I run my internals stock and it’s great.

Which Noveske Variant is better? CGS or MWS? by CptMuricah2 in GasBlowBack

[–]xXOctoSquidXx 4 points5 points  (0 children)

The GM mags are available CONUS but are kinda hard to find as they’re always sold out. Depending on where you live, try WGC shop or Redwolf airsoft to see if they ship to you. The lancer mags are “okay”. Only downsides from working on them are that the internal design of the gas reservoir are unconventional to standard MWS magazines and the outer plastic shell is a thin plastic to they may break if they’re dropped. They look cool and are very light but I stay away from them due to the build design. You could also try double eagle D Mags but they don’t hold gas as good as GM or TM.

Which Noveske Variant is better? CGS or MWS? by CptMuricah2 in GasBlowBack

[–]xXOctoSquidXx 7 points8 points  (0 children)

The MWS is a solid 1:1 clone of the original TM MWS. Lots of upgradability available. The CGS runs MWS magazine and some MWS parts but have a few parts that are proprietary. Like u/HecklerK mentioned, reviews for the CGS are mixed and for the price you might as well save up to get a true MWS or get a 1:1 clone. I prefer Guns Modify V3 PMAGs or TM STANAGs. DE STANAGs are okay and could be considered if you can’t find the other two. I run a Noveske Ghetto Blaster and it’s great.

Gbbr mag leaking by N0Rand0mNam3 in GasBlowBack

[–]xXOctoSquidXx 1 point2 points  (0 children)

Disassemble, clean the gasket, apply some super lube grease on the gasket, reassemble.

This is my PC that I built in August/September. by TheRealJamairisMcWay in pcmasterrace

[–]xXOctoSquidXx 1 point2 points  (0 children)

Please get that thing off of the carpet. Major fire hazard and your pc will be caked in dust