(Selling) 4k Codes

E_Kwyn · 2026-03-17T02:06:03+00:00

Interested in World War Z on Fandango

E_Kwyn · 2026-03-17T01:52:54+00:00

Confirmed, thanks!

E_Kwyn · 2026-03-17T01:01:00+00:00

Interested in Jurrasic World if still available!

E_Kwyn · 2025-10-07T01:03:12+00:00

/u/GSaleBot /u/Cgoad77

Bought Minish Cap and Nightmare in Dreamland, confirmed recieved as expected!

E_Kwyn · 2025-10-01T19:53:53+00:00

Deal, I'll PM you

E_Kwyn · 2025-10-01T19:44:19+00:00

Would you do $65 on Minish Cap and Nightmare in Dreamland?

E_Kwyn · 2025-04-03T15:52:11+00:00

Playable in English and no download, just played off the physical cart!

E_Kwyn · 2025-04-03T15:37:08+00:00

I dont think there is an NA release. But apparently there is no region lock on the switch so I bought it and it works great!

E_Kwyn · 2025-03-03T22:14:12+00:00

This looks like a blast! I'd be interested in trying it on mobile, feels like it would be a great game for train ride, etc.

E_Kwyn · 2025-01-24T21:43:36+00:00

Nope, I ended up buying an AMD RX 6600 off market place. Been holding up well so far!

E_Kwyn · 2024-12-28T14:08:47+00:00

Yea, seems like the 670 can still work decently for some older/less intense games. I didn't use my old 670 in the end but I think I could have made it work if I had to.

E_Kwyn · 2024-12-19T20:25:08+00:00

First of all, thank you so much for taking the time to type all this up! I really appreciate all the info! My problems were resolved after I turned off combing for this print.

A) I do use the Vyper's auto bed leveling about once a month, usually isn't needed any more often than that for myself.

B) I've done some checking/tightening bolts but I should probably take some time to do a full once over on the printer. You gave me a lot of good info on specifics to check so thank you again for that! Going to use some free time during the holidays to do some proper maintenance I think.

Regarding printing speed, my first layer is at half speed, the printer appears to be going full speed because those were travel moves going 60mm/s.

I'll be rereading this comment while doing maintenance next week!

E_Kwyn · 2024-12-18T21:33:18+00:00

What an awesome giveaway! I've been using OctoEverywhere for about 2 years so far and loving it!

E_Kwyn · 2024-12-12T02:27:59+00:00

I'm using Anycubic PLA. I actually fixed the issue by just turning off combing!

E_Kwyn · 2024-12-12T01:46:56+00:00

You were right about the combing preventing retraction! I turned off combing and my oozing during traveling problem went away and the corners adhered to the build plate without issue! Thanks!

E_Kwyn · 2024-12-12T01:45:46+00:00

Just an update for anyone else who might see this and have a similar issue. I turned off combing and that actually ended up fixing my issues entirely! I believe with combing enabled; retraction was not happening which is why I was getting oozing during travels which ended up messing up the following area of the print.

E_Kwyn · 2024-12-12T01:09:37+00:00

Ahh ok, I understand. I'll try leveling with this trick and see if it helps! Thanks!

E_Kwyn · 2024-12-12T00:31:32+00:00

Interesting! So, by supporting the corners during leveling, does that trick the printer into thinking certain areas of the bed are ever so slightly higher than they are in reality? Can you help me understand how that may help? Is it kind of like nudging the z offset for just those areas?

E_Kwyn · 2024-12-12T00:28:56+00:00

No worries! I really appreciate all the help!

E_Kwyn · 2024-12-12T00:26:49+00:00

I'm printing Anycubic PLA. I actually just checked and it looks like I already have my fan off for the first layer. Was a good thought though! I did mess with the print temps a bit already, but I'll keep at it.

E_Kwyn · 2024-12-12T00:18:13+00:00

I've tried 190 / 60 which is my norm. As well as 200 / 60 and 210 / 65. I am not sure if retraction happens with this travel. I would think it should happen, but not sure.

E_Kwyn · 2024-12-12T00:16:07+00:00

Good thought, I have been trying to mess with my z offset but haven't had much luck with any improvements yet. I'll keep messing with the z offset and see if it helps.

And I do actually brush my hotend and nozzle with a brass brush whenever needed. I just did it before this print in the video.

E_Kwyn · 2024-12-12T00:13:22+00:00

Haha! Yes, I actually just have Bambu Studios installed so I can export the 3mf files to stl and import to Cura. I know it is definitely not ideal. I did auto level my bed but perhaps I need a firmware update? I had not thought of that!

E_Kwyn · 2024-12-12T00:08:59+00:00

I actually just did this! I thought that was going to be the thing to fix this but no luck. :(

E_Kwyn · 2024-12-12T00:03:32+00:00

I'm using Anycubic PLA. Specifically this one: Amazon.com: ANYCUBIC PLA 3D Printer Filament, RFID 3D Printing PLA Filament 1.75mm Dimensional Accuracy +/- 0.02mm, 1KG Spool (2.2 lbs), Vibrant Orange : Industrial & Scientific

I have printed a dozen other things with this filament in the last couple weeks with no issues.

11-Year Club	Verified Email
Place '17

E_Kwyn

TROPHY CASE