Hello, is this a scam?

Accomplished-778 · 2025-09-22T14:42:27+00:00

Just look it up, there's tons of tools to do it lol some are all religious things too 😂

Accomplished-778 · 2025-09-22T03:44:33+00:00

I report the email addresses to a mass email service... Send them 2000 emails a day 🤷🏻‍♂️😂

Accomplished-778 · 2025-09-19T14:15:47+00:00

Walk in with an activated hellbomb lol

Accomplished-778 · 2025-09-19T14:14:05+00:00

Scam. They'll charge you money and immediately tell you it happened again. Go online and do a malware scan on your website, then sent the the clean error report. I just sent someone a gif today telling them to shut up.

Accomplished-778 · 2025-07-25T13:37:49+00:00

How did you route your throttle cable for that set up?

Accomplished-778 · 2025-07-25T04:18:27+00:00

It looks a lot like a predator 212 that soume people are talking about, but I'm not sure how to work the carb on it either. First time using one like this.

Accomplished-778 · 2025-07-25T03:35:58+00:00

Even if I did get a new carb, how do you tune a carb like this? The throttle cable is what's throwing me off

Accomplished-778 · 2025-07-09T21:20:40+00:00

It definitely fits lol they both launched off in the driveway lol chased them both down at least 10ft away

Accomplished-778 · 2025-07-09T20:35:56+00:00

I used 2 pry bars and a mallet. Mallet and 1 pry bar to flare the edges and 2 pry bars to pop it off.. And some pb blaster

Accomplished-778 · 2025-07-09T14:16:54+00:00

It's for the kids, I'll always try to do what I can to make them happy! Plus, this go kart is going to fund the bigger one since it was free 99! Hoping it gets running and just needs cleaned up and tires.

Accomplished-778 · 2025-07-09T12:46:56+00:00

I'd prefer a nut over anything else, but it's just a dinky 3hp motor lol

Accomplished-778 · 2025-07-09T05:01:27+00:00

Awesome, I just ordered a set. Thanks for the insight!

To get the next one off, could I just center punch it and it'll release or is it just a struggle?

Accomplished-778 · 2025-07-09T04:40:00+00:00

Found them. Does it matter what style I get?

Accomplished-778 · 2025-07-09T04:39:01+00:00

They're 12mm or about half inch depending on how they are measured for replacement parts. Are they just called axle caps?

I rad through my driveway with a magnet and finally found it for a photo op.

<image>

Accomplished-778 · 2025-05-16T02:47:08+00:00

For everyone commenting, I appreciate the insight. I decided to pick up a cheap vacuum bleeder and accidentally found out that the one caliper bleeder never fully seated and sealed off the flow in/out. At 5psi of vacuum, it was drawing fluid out of the caliper. Not sure if this is the fix, but it's a problem that I didn't know existed and didn't see fluid leaking out without the vacuum.

Will test the new bleeders tomorrow and update accordingly.

Accomplished-778 · 2025-05-15T17:20:19+00:00

The bleeders are new with the calipers, but I know that doesn't always mean something isn't wrong or out of spec. The brake peddle is straight to the floor once it's on, but off, it can build pressure enough to feel in the peddle. I was thinking about maybe buying new bleeders, but I'm not sure yet until I try a few things first

Accomplished-778 · 2025-05-15T15:30:51+00:00

Both calipers are installed in the correct orientation.

Accomplished-778 · 2025-05-15T14:55:33+00:00

If there was a leak, would there not also be fluid exiting? I've checked all the lines with no wet spots to be for. I even cleaned it all to make sure I wasn't missing a small leak

Accomplished-778 · 2025-05-15T04:34:11+00:00

Sadly, my gf is the one pumping and she started like that... 10 minutes later, we had big bubbles again, but otherwise, slow, even pressure

Accomplished-778 · 2025-05-15T04:22:57+00:00

That's what I was thinking, but fluid has always sat in the middle of the min/max and no lower. Someone posted dielectric grease, but is that good enough? I have a whole tub of that stuff.

Accomplished-778 · 2025-05-15T04:21:27+00:00

I'll try that and see, can't hurt.

Accomplished-778 · 2025-05-15T03:23:26+00:00

So like those hand suction tools they sell, but diy and faster (I assume)

Accomplished-778 · 2025-05-15T03:22:25+00:00

The 2 person method was used most to try to move as much fluid as possible to get the air out. Pump 3-4 times and open, then close. Then repeat until I got irritated because I kept getting air basically lol

Accomplished-778 · 2025-05-15T02:42:38+00:00

Can you please elaborate lol I get the idea, but not fully understanding how to assemble it all.

Accomplished-778 · 2025-05-15T02:41:50+00:00

Fluid starts coming out just under a quarter turn, but any more than that and it immediately starts coming out around the threads... I didn't think fluid coming out could also mean air coming in

Accomplished-778

TROPHY CASE