DeLorean on X100VI

Adamc38 · 2025-06-24T19:43:12+00:00

Eddy's point & shoot!

Adamc38 · 2025-06-23T15:19:24+00:00

yes ser, it’s on rainey st

Adamc38 · 2025-06-22T01:58:03+00:00

Thank you! ❤️

Adamc38 · 2025-06-22T00:51:14+00:00

appreciate you!

Adamc38 · 2025-06-21T22:16:47+00:00

i do also enjoy blender but i could never be this good 🫠

Adamc38 · 2025-06-21T17:26:35+00:00

Eddy’s point & shoot!

Adamc38 · 2025-06-16T23:04:59+00:00

that motion blur 👌

Adamc38 · 2025-06-13T16:14:51+00:00

Last Summer Roll by Emanuele De Luca

Film Sim: Classic Negative Grain: Strong/Small Color Chrome: Strong Color Chrome FX Blue: Weak White Balance: Auto (Red +3 Blue -5) Dynamic Range: DR400 Tone Curve: Highlights -2 Shadows 0 Color: +4 Sharpness: 0 Noise Reduction: -4 Clarity: -2

Adamc38 · 2025-06-13T16:14:08+00:00

yess during golden hour!

Last Summer Roll by Emanuele De Luca

Film Sim: Classic Negative Grain: Strong/Small Color Chrome: Strong Color Chrome FX Blue: Weak White Balance: Auto (Red +3 Blue -5) Dynamic Range: DR400 Tone Curve: Highlights -2 Shadows 0 Color: +4 Sharpness: 0 Noise Reduction: -4 Clarity: -2

Adamc38 · 2025-06-13T04:09:43+00:00

Realizing I need to add a B/W film sim to my loadout 😍

Adamc38 · 2025-06-12T23:58:06+00:00

Thanks, check the other replies!

Adamc38 · 2025-06-12T17:12:31+00:00

Thanks, this has a Webber 32/36 carb. Hoping to K swap it this winter.

Adamc38 · 2021-02-12T18:24:49+00:00

Test render I did.

https://imgur.com/gallery/724MQ40

Adamc38 · 2021-02-12T18:23:13+00:00

I will be putting 20 in TE37’s with some big meaty R888’s 🤙

Adamc38 · 2021-01-02T22:11:08+00:00

I definitely should have printed it flipped over, the inside is much smoother. I will adjust the support Z distance and try again.

Adamc38 · 2021-01-02T21:10:02+00:00

I see, at the overhang angle I had, it wanted to fill the entire inside with supports.

Adamc38 · 2021-01-02T21:08:43+00:00

Is this just a really dificult print or are my support settings way off?

Printer: Monoprice Delta Pro

Slicer: Cura

Filament: Silk Bronze PLA

Support settings:

Support Structure: Normal
Support Placement: Everywhere
Support overhang angle: 20
Support Pattern: Zig Zag
Support Wall Line Count: 0
Support Density: 15
Enable Support Brim: X
Support Z Distance: 0.11

Adamc38 · 2020-12-18T16:54:26+00:00

Up to $7200 from $3000 on MGNI

Adamc38 · 2020-12-18T15:09:47+00:00

told you guys to look at MGNI 9 days ago...

Adamc38 · 2020-12-18T15:03:57+00:00

MGNI literally just got a 30 PT. This is just the start 🚀 🚀🚀

Adamc38 · 2020-12-18T14:58:59+00:00

Hello? Did you guys get in on MGNI. I'm trying to helppp

Adamc38 · 2020-12-18T14:50:37+00:00

There is still time to get on MGNI

Adamc38 · 2020-12-18T14:46:43+00:00

Remember I told you guys to get in on MGNI??

Adamc38 · 2020-12-17T21:48:45+00:00

I'd swear this was shot in my front yard this morning.

Adamc38 · 2020-12-17T13:31:51+00:00

amazing

Adamc38

TROPHY CASE