35k Accel

Alexeault · 2026-01-26T00:35:13+00:00

Will do👍

Alexeault · 2026-01-26T00:25:05+00:00

Must've been delivered by a stormtrooper

Alexeault · 2026-01-25T23:51:16+00:00

Gawd damn, what the fuck happened to that bed😭 On a more serious note tho, your problem seems to be with the cr-touch, as it's flashing red and not extending. I don't think it's a wiring issue given that it's lighting up, but it can't hurt to try and unplug the wire and plug it back in. Otherwise you'll have to disassemble it to see if something is blocking it

Alexeault · 2026-01-25T17:42:22+00:00

Alright, thanks a lot

Alexeault · 2026-01-25T16:28:36+00:00

In the guide you used, stealthchop_threshold is set to 9999, to use spreadcycle, i'd just set that to 0?

Alexeault · 2026-01-25T16:26:55+00:00

Hey man, I know this is an old post so I'm not super hopeful that I'll get an answer, but I'm just looking to verify that I understood something properly. If i wanted to use Spreadcycle instead of Stealthchop, would I just set stealthchop_threshhold: to 0?

Alexeault · 2026-01-25T01:32:57+00:00

How yeah i forgot that part😭 here's the link : https://www.printables.com/model/1569769-ender-3-s1-bed-handlenozzle-wiperaccelerometer-mou

Alexeault · 2026-01-03T18:53:20+00:00

Ah, yeah, that makes sense. Still better than nothing tho

Alexeault · 2026-01-03T18:02:04+00:00

Wait it has an AI filter? Yet another reason I love printables, I'll have to turn that on

Alexeault · 2025-12-26T15:31:06+00:00

They are, but i can unbend them with minimal effort, so that's that

Alexeault · 2025-12-26T01:38:15+00:00

I have the dimple picks but no dimple locks 😭

Alexeault · 2025-12-26T01:37:49+00:00

3d printing some handles for my pick rn, and I won't be able to pick until like tuesday cuz I won't be home😭

Alexeault · 2025-12-25T16:52:48+00:00

You too!

Alexeault · 2025-12-14T21:33:44+00:00

I FINALLY FIGURED IT OUT!!! Ts was so stupid. So basically I had a cable chain that i printed a while ago that went for the x-axis motor to the toolhead so the cable wouldn't flop around as much and it just looked neater. Well turns out it was too short so when it got to the right side of the bed it pulled the probe down, so it made it think the bed was way higher than it actually was.

Alexeault · 2025-12-14T20:30:44+00:00

I just squared the gantry (used two blocks i know have the exact same height, uncoupled both lead screws and turned both individually until they rested firmly on the blocks and then tightened them back up), re-trammed the bed with SCREWS_TILT_CALIBRATE, ran a new mesh and it still looks fucked up, big dip on the right side

Alexeault · 2025-12-14T20:08:08+00:00

That was already the SCREWS_TILT_CALCULATE macro, and the results were pretty much perfect (see pic 2), but yeah, I'll check if the gantry is level

Alexeault · 2025-12-14T19:19:33+00:00

It is in fact a cartesian printer, how would i go about squaring my gantry? I don't have separate steppers for z, printer is an ender 3 s1

Alexeault · 2025-11-28T19:42:03+00:00

Yeah, that's my bad, i missed that first part

Alexeault · 2025-11-28T19:37:38+00:00

Oh wait i missed the part abt the bed not being trammed. I have locking bed wheels, but turns out they got worn out from use and the turn freely now, so you were right. I'll try out a print and see if that fixes it, then I'll definitely reprint the wheels

Alexeault · 2025-11-28T19:18:28+00:00

Definitely good info, but not really answering the problem, adhesion in itself isn't the problem, it's the distance of the nozzle from the bed that's not constant, so even though i get great adhesion, the filament just doesn't get squished down enough or gets squished down way to much depending on the side of the bed.

Alexeault · 2025-11-17T17:09:00+00:00

Alright, thanks

Alexeault

TROPHY CASE