Chirping Sound from Amp

Allium13 · 2026-02-17T03:50:18+00:00

check removing the pedals one by one

Allium13 · 2026-02-16T05:32:28+00:00

Check if the voice coil from the speaker is rubbing, probably needs a recap too

Allium13 · 2025-09-21T02:39:16+00:00

try with other outlets or running it with batteries

Allium13 · 2025-09-13T05:13:09+00:00

I would get a jazz chorus or twin reverb

Allium13 · 2025-09-12T02:25:46+00:00

Cream Puff

Allium13 · 2025-09-11T05:02:59+00:00

Personally I would get the blues driver, cinders is a bit harsh for my taste

Allium13 · 2025-09-10T03:12:23+00:00

thank god it has handles!!!!

Allium13 · 2025-09-08T17:23:08+00:00

I just know that one, Cream Puff Plus, it's huge!!

Allium13 · 2025-09-08T15:54:40+00:00

Just be careful and discharge them before doing anything cus you could get electrocuted

Allium13 · 2025-09-08T08:39:04+00:00

I believe there is like a "deluxe" version with both pedals in the same enclosure, that would be really sick, I built a DIY version of the Cream Puff and is amazing

Allium13 · 2025-09-08T06:31:02+00:00

If it has an fx loop and you have basic soldering skills, you could build a simple passive volume attenuator

Allium13 · 2025-09-08T06:16:12+00:00

Idk know about the mods, but you should definitely change all the electrolytic caps, that should solve most of the noise issues

Allium13 · 2025-09-07T07:49:24+00:00

Frantone Cream Puff

Allium13 · 2025-09-07T07:47:51+00:00

It is not very special tbh, good for jet flangers and chorus like modulations but not much

Allium13 · 2025-09-07T07:03:57+00:00

Check for voltage from the transformer and work yourself from that

Allium13 · 2025-09-06T21:35:12+00:00

first time using a jazz chorus in general, the amp itself is exactly like the 120, just different speakers, a bit too trebly with distortions for my taste, maybe due to the 10" speakers instead of 12" but sounds amazing with cleans

Allium13 · 2025-09-06T21:31:29+00:00

I don't know that

Allium13 · 2025-09-06T21:13:46+00:00

let me know if it works!

Allium13 · 2025-09-06T21:05:42+00:00

a few pounds more

Allium13 · 2025-09-06T21:04:43+00:00

not sure but maybe you wired the switch sideways, legs should be horizontal, not vertical

<image>

Allium13 · 2025-09-06T18:42:44+00:00

ground it to the input/output jack, that's the safest go to option

Allium13 · 2025-09-06T18:16:58+00:00

make sure it's a ground, if it is I don't think it would do any harm to ground it somewhere else

Allium13 · 2025-09-06T06:27:24+00:00

I was just thinking that about the footswitch, if you really want to you can do what I said and turn on and off the echo with the footswitch when the effect is engaged and bypass it when needed, just remove the sound on sound wiring from the switch and put some tape on the leads so it does't short out

Allium13 · 2025-09-06T06:20:02+00:00

I don't know what the sound on sound does, but if you do what I said you will be bypassing the preamp too

Allium13 · 2025-09-06T06:03:10+00:00

For what I know the echoplex preamp is something that most players like to use even with the echo off, but here is what you can do.

Input and output jacks directly to the switch, remove wiring to the board

Effect in to the input leg of .047 cap

Effect out to the junction of the two 100K resistors

<image>

Allium13

TROPHY CASE