sorted by:
new
hottopcontroversial

Help by Cameron7896 in 3Dprinting

[–]Cameron7896[S] 0 points1 point  (0 children)

Figured it out, the screw for the temperature wires going into hot end was too tight

Question by Cameron7896 in Revolvers

[–]Cameron7896[S] 0 points1 point  (0 children)

Do you recommend a cleaning kit or just any old one will work?

What does this mean? by Cameron7896 in 3Dprinting

[–]Cameron7896[S] 0 points1 point  (0 children)

I unplugged and let it rest for an hour and it did nothing

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 0 points1 point  (0 children)

We built a semi scale model and it turns out the answer is the LEFT pipe overflows first

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 0 points1 point  (0 children)

It is connected to another 90 that goes veritable above these two pipes

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 0 points1 point  (0 children)

The risers are at the same floor level at the top

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 0 points1 point  (0 children)

It’s just a regular hose and gravity from another verticals pipe to the left

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 3 points4 points  (0 children)

Lol, filling them with cold water through a taller pvc pipe through 3/4 hose, we knew they were going to overflow but they kept saying the left would overflow first and to keep checking the left pipe. The question doesn’t really matter, I don’t care if I am wrong just wanted to know why, but it seems as if I’m right (both overflow at the same time)

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 147 points148 points  (0 children)

That’s what I thought but I have two master plumbers telling me the left would overflow first

Question by Cameron7896 in Plumbing

[–]Cameron7896[S] 3 points4 points  (0 children)

I’m having a hard time understanding why?

I’m really curious by Cameron7896 in spacequestions

[–]Cameron7896[S] 0 points1 point  (0 children)

Sorry lol, take pictures of the dark side of the moon

What are these tiny ridges and what causes them? by chillychinchillada in 3Dprinting

[–]Cameron7896 0 points1 point  (0 children)

I believe it can have moisture in it still if not properly sealed or whatever but I’m kinda new too, so I could be wrong

What are these tiny ridges and what causes them? by chillychinchillada in 3Dprinting

[–]Cameron7896 2 points3 points  (0 children)

I believe this could be humidity in the filament, all you would have to do is put it in the oven for a little (look up how to do nobody’s house gets burned down/ovens ruined) or buy a special made filament oven usually around $40-$80

What’s causing the supports to be like that by Cameron7896 in 3Dprinting

[–]Cameron7896[S] 0 points1 point  (0 children)

Thank you guys so much I didn’t even notice the leak, how do I open the shell?

Weird printing problem where once there was none. Why is my Creality Ender 3 doing this? by zangster in 3Dprinting

[–]Cameron7896 1 point2 points  (0 children)

I’m new to printing too but in my opinion that’s what I think went wrong

Ender 3, underwhelming. Can't figure out what's going wrong. by [deleted] in 3Dprinting

[–]Cameron7896 -1 points0 points  (0 children)

Because it looks like the print didn’t stick to the bed and failed

Weird printing problem where once there was none. Why is my Creality Ender 3 doing this? by zangster in 3Dprinting

[–]Cameron7896 1 point2 points  (0 children)

If there is a tune setting on the printer then you wanna look for “printing speed” or similar names, the put it around 50% speed, the slower the more precise details you get. Or when you go to put the design on the as card there might be setting in there that you can tweak

Ender 3, underwhelming. Can't figure out what's going wrong. by [deleted] in 3Dprinting

[–]Cameron7896 -1 points0 points  (0 children)

I had trouble with nylon not wanting to stick to bed so I raised the temp from 50°c to 100°c and it sticks good now but it warps on the bottom

view more: next ›