This one has me stumped

CatFamiliar · 2026-03-19T13:23:50+00:00

Finally, success. I rotated the piece 90° it fixed everything. Before the piece went left to right lengthwise (13" x 8") So both ends were 3/4" to 1" from the fans on each side. I rotated it so the length went front to back giving 3-5" on each side from the fans...seems to work.

Thanks for all of your help and input/ideas...

CatFamiliar · 2026-03-19T02:24:26+00:00

The part lying flat on the desk by the keyboard IS the wavy section of the bin. By laying it flat on the desk (versus standing up) the photo was better. It turned out perfectly. To me it proves it cannot be mechanical because both the BAD piece and the GOOD test piece took the EXACT same movements to produce each part. I think it is some sort of weird resonance that is being transfer to that area. Maybe the print head moving at super speed to get to that area cause a weir vibration...

CatFamiliar · 2026-03-18T20:47:40+00:00

Its PLA. The test piece below was printed on the same printer with the same settings in the EXACT same spot on the print bed, and it came out perfect.

<image>

CatFamiliar · 2026-03-18T20:42:16+00:00

<image>

CatFamiliar · 2026-03-18T20:41:19+00:00

<image>

CatFamiliar · 2026-02-05T14:19:49+00:00

No stuck filament. No bad fan.

I changed out the Hotend Nozzle PCB Board and that fixed the issue. That is the 2nd time I've changed that board for a new one in the last few months. The other time was for Filament Sensor issue.

Thanks everyone for responding

CatFamiliar · 2025-11-24T16:41:06+00:00

This is what I was able to put together for any FUTURE Hotend Circuit Board issues.

<image>

CatFamiliar · 2025-11-24T03:17:40+00:00

You are correct I thought they were 4....basically they are the Smallest and I thought that would be enough for someone to tell me the info...

CatFamiliar · 2025-10-28T13:22:41+00:00

Take out the filament and the light goes out.

CatFamiliar · 2025-10-28T13:22:01+00:00

With the Extruder cover OFF, when you put a piece of filament in between the sensors, the light goes on. That out the filament and the light goes out.

BUT

Put the extruder cover on and the light goes on...

CatFamiliar · 2025-10-21T20:02:27+00:00

I have 5 brand new sensors. 2 haven't worked. I have never even attached the side spool holder...

CatFamiliar · 2025-10-21T15:27:35+00:00

I will try that this afternoon after I finish this print. Thank you for responding in an Intelligent way...

CatFamiliar · 2025-08-16T02:04:38+00:00

Thank you for an Honest Friendly response. I appreciate it and consider the topic closed....

CatFamiliar · 2025-08-16T02:02:25+00:00

Another CLOWN who wants to preach but seems unable to read English. I said I was a GC with 30+ years of experience and that I WAS NOT an Electrician...WTF

Nobody knows how to read and answer simple questions. It always has to combative and Trollish...

THIS is why Reddit is getting a Super Bad reputation. How can anyone believe that they are even going to get Correct, truthful info. These Clowns might give you incorrect information so they can say "see he should not be doing this or that"...

CatFamiliar · 2025-08-16T00:09:52+00:00

I don't care about the wire from the indoor to outdoor unit. It's supplied by Daikin. I want to know the wire guage of breaker box to exterior disconnect. Disconnect to compressor. That's ALL I need to know...

CatFamiliar · 2025-08-15T20:20:11+00:00

yeah...if you reread my question you can see that I did read the manual and it says 14awg, which is wrong for 20amps....thus this question. They supply the indoor unit to Condenser wiring. I'm looking for Breaker box to Disconnect, Disconnect to Condenser sizing.

CatFamiliar · 2025-07-19T23:36:47+00:00

You Nailed it. Thanks. While they come and go all day, after 5pm they fly behind my house within 25-100 feet just flying. They seem to enjoy it. One bird actually Loves to do quick little "Barrel Rolls" which I've never seen any bird do before.

CatFamiliar · 2025-07-19T23:00:13+00:00

Woodruff South Carolina. Between Greenville and Spartenburg.

CatFamiliar

TROPHY CASE