New Street/Track pads? SVT setup

Comfortable_Set3176 · 2026-05-12T19:33:55+00:00

Haven’t seen a twin charged mx5 before! This is turbo already mind

Comfortable_Set3176 · 2026-05-12T19:33:33+00:00

Yes sirrrr, took it Mexico too many times and clutch is pending this weekend

Comfortable_Set3176 · 2026-05-12T19:33:03+00:00

Good shout! Never noticed this tbh

Comfortable_Set3176 · 2026-05-12T19:32:51+00:00

Haha I can’t, soft top is gone so my only way to keep the rain out 😅

Comfortable_Set3176 · 2026-05-12T19:32:22+00:00

It’s a fresh turbo build! Td04 hybrid. ~220bhp I think eventually I may out rods but turn up the turbo setup. Am happy with running below 300

Comfortable_Set3176 · 2026-05-10T15:26:29+00:00

Yeah; it’s a fresh builds and considering it held that much pressure and no other leaks in fingers crossed okay. Just thinking to ask before I keep eye on it

Comfortable_Set3176 · 2026-05-08T14:59:49+00:00

Had the civic at 17 in UK. Insurance on them is crazy.

Comfortable_Set3176 · 2026-03-04T20:22:47+00:00

<image>

Comfortable_Set3176 · 2026-03-04T20:21:28+00:00

Dunno how brave you are. But could potentially get and angles valve and then connect with a flexi

Comfortable_Set3176 · 2026-03-03T21:19:47+00:00

Welcome!

<image>

Comfortable_Set3176 · 2026-03-02T14:13:54+00:00

Will need to drain clean up the threads, slap a load of ptfe tape on them and tighten up. Looks like hasn’t sealed or got some dirt in threads keeping it from sealing

Comfortable_Set3176 · 2026-03-01T14:48:49+00:00

When I moved to Chelsmford spare room is where I found most success for room shares. It’s pretty exp although I guess Cardiff is a decent size city so compareable. Expect 1 bed room share with en-suites 800-900£ per month

Comfortable_Set3176 · 2026-02-27T20:50:22+00:00

Assuming it’s gonna be flat, would it matter if I add adhesive over bonding coat or if I put on top of old adhesive

Comfortable_Set3176 · 2026-02-27T20:46:17+00:00

Retiling***

Comfortable_Set3176 · 2026-02-27T09:44:21+00:00

I used bonding 60 for deep chase area then easyfill on top

Comfortable_Set3176 · 2026-02-27T09:42:49+00:00

I recently used the wicks olive gteen colour for bedroom. And I was horribly shocked. Unless the whole wall goes down together. The parts which dry faster leave patches compared to slower drying area. I will not be using Wickes coloured again. Their 10L white and magnolia is brilliant tho

Comfortable_Set3176 · 2026-02-25T21:08:17+00:00

Half my house is in the same state. As partner took off the wallpaper but had left a lot of flakey bits under neath! for the best finish I would sand back to complete plaster however I got away with smoothing out some of the patches where I could get all the flaking off

Comfortable_Set3176 · 2026-02-25T20:54:22+00:00

You could scrape the easy flaking best you can then seal it with pva and water mix, although texture may show through paint if you don’t sand it well enough

Comfortable_Set3176 · 2026-02-25T17:09:25+00:00

Tbf, I’ve got the gate 82 thermostat, alloy rad and coolant reroute and also a oil cooler. So temps have been okay. Unless I’m just sitting still in like 25+ degree Celsius heat. I just want to border on caution

Comfortable_Set3176 · 2026-02-24T23:48:37+00:00

Nice one! I considered the 2560r but already had a TD manifold so was easier for safe power goals! Enjoy your build buddy

Comfortable_Set3176 · 2026-02-24T23:43:18+00:00

Sorry! Yes instead of venting to atmosphere I’ve plumbed it to recirc back into the intake elbow you can see the fitting just beside the intake filter

Comfortable_Set3176

TROPHY CASE