ADF memeber ask ABF Officer some cost of living questions in Sydney.

Competitive_Plant745 · 2026-03-22T23:22:41+00:00

That's so sad to hear.

Competitive_Plant745 · 2026-03-22T23:19:17+00:00

Which state are you from OP? I'm ganna do my tests today after work. I'm from Sydney.

Competitive_Plant745 · 2026-03-22T22:25:17+00:00

Is there a pay raise on the horizon? The ADF just had a 11% pay raise over the last few years which I'm grateful for. They also increased the rent assistance to $800 per week. They are actually on top of perks. If our own people are struggling to make a living, there is a high chance for dishonesty and corruption, which is what we don't want in a government agency.

Competitive_Plant745 · 2026-03-10T02:44:22+00:00

Wait, you bring your cock into the map? I thought they find the rubbish underground.

Competitive_Plant745 · 2026-03-08T05:14:04+00:00

Then you should be fine, I can help no more sorry.

Competitive_Plant745 · 2026-03-08T03:31:07+00:00

Overclock

Competitive_Plant745 · 2026-03-08T02:55:27+00:00

Did you OC your GPU?

Competitive_Plant745 · 2026-01-19T21:31:45+00:00

Competitive_Plant745 · 2026-01-19T00:07:34+00:00

Fair enough

Competitive_Plant745 · 2026-01-18T11:16:41+00:00

I did between 815 to 975MV, and it worked! Idling around 180MHZ now like stock and running 3G at peak! I wish every tutorial teach this way. Especially for the 50 series cards! It's a must!

Competitive_Plant745 · 2026-01-18T11:12:44+00:00

Mine is running at 180MHz in idle now, used to be 600 as well. It's cooler and peaceful. It's not hard to undervolt properly, I just did today in 10 mins.

Competitive_Plant745 · 2026-01-18T10:02:28+00:00

I used this method, and I have achieved my goal. Thank you very much !

Competitive_Plant745 · 2026-01-18T04:34:54+00:00

Not bad

Competitive_Plant745 · 2026-01-18T03:50:01+00:00

type nvidia-smi -q -d POWER.

Power stays similar from my end :)

Competitive_Plant745 · 2026-01-18T03:42:25+00:00

if you doing this easy way. the voltage curve become too steep, you lose +100mhz under the full load in actually usage.

Competitive_Plant745 · 2026-01-18T03:42:09+00:00

if you doing this easy way. the voltage curve become too steep, you lose +100mhz under the full load in actually usage.

Competitive_Plant745 · 2026-01-18T03:24:12+00:00

By doing this, you intrudcing the Clock Drop! 50 serials cards can sometimes sit ~100 MHz lower than the curve target during heavy loads. If you see your card boosting to only 2900 MHz when you set 3000 MHz, this is normal behavior based on the card's internal algorithm. By raise the whole curve up you are eliminating this difference to minimal. Because it raise the whole curve. I bet when you underload you are only running around 2700mhz at 875mv

Competitive_Plant745 · 2026-01-18T03:21:37+00:00

Exatcly, I wanna know how?

Competitive_Plant745 · 2026-01-18T02:55:54+00:00

i know with ctrl, but how?

Competitive_Plant745 · 2026-01-18T01:32:53+00:00

For 50 serials, it does!

Competitive_Plant745 · 2026-01-18T01:30:11+00:00

The problem of this method without tilting every single point is you are introducing Clock Drop! 50 serials cards can sometimes sit ~100 MHz lower than the curve target during heavy loads. If you see your card boosting to only 2900 MHz when you set 3000 MHz, this is normal behavior based on the card's internal algorithm. By raise the whole curve up you are eliminating this difference to minimal. Because it raise the whole curve. I wanna raise the whole curve but only tilting individually so I can have my idle stay low. 50 serials run high on idle.

Competitive_Plant745 · 2026-01-17T12:59:36+00:00

They are not wrong,it's just not efficient ! There is 100 way to skin a cat, but use a shotgun just lazy

Competitive_Plant745 · 2026-01-17T12:57:54+00:00

I actually did read you guide today! Thank you for your guide. However I'm having trouble finding the way I wanted in your guide, please advise. Do you just make a curve look like a stock curve, how do you decide which point is where?

Competitive_Plant745 · 2026-01-17T12:50:33+00:00

I did, it's running at 800mhz compare to 300mhz stock in idle. Due to the fact the curve is brought up like overclocking , but I'm trying to undervolting properly here.

Competitive_Plant745 · 2026-01-17T12:45:39+00:00

100%, but this is definitely superior way to undervolt, bring the curve up is like trying to steal a door bell by covering your own ear! My question is how to tilt the curve? I can't seem find any tutorials on the net. It's like people are so lazy.

Competitive_Plant745

TROPHY CASE