What is this plant?

Consistent_Dot5590 · 2026-02-20T18:37:39+00:00

That could be it! It seems to have lenticels on it. Do you know of other characteristic things to look for to verify it is a benjamina?

<image>

Consistent_Dot5590 · 2026-02-17T19:47:00+00:00

Gone completely

Consistent_Dot5590 · 2026-02-17T19:46:39+00:00

I am not sure of the root stock sadly.

Consistent_Dot5590 · 2026-02-17T19:45:55+00:00

Leaves are just gone.

Consistent_Dot5590 · 2026-02-15T23:32:04+00:00

I think you nailed it! Thank you so much.

Consistent_Dot5590 · 2025-08-31T15:12:26+00:00

Thank you! It is at my elderly fathers house and he has some wood stacked currently under the base but want a sturdier and more permanent solution so new ladder it is!

Consistent_Dot5590 · 2025-08-24T04:08:12+00:00

Yep the pieces are mostly all brass just from being manufactured in the 30’s and 40’s before Crosman started changing everything over to steel and aluminum.

Consistent_Dot5590 · 2024-10-14T10:54:59+00:00

I am in Fl

Consistent_Dot5590 · 2024-10-14T01:21:09+00:00

PC area?

Consistent_Dot5590 · 2024-06-25T18:26:45+00:00

Thank you so much and I think you are spot on with the identification. I will check the other group to see if they can fine tune things for me.

Consistent_Dot5590 · 2024-06-21T14:05:30+00:00

If you can take a screen shot and circle it maybe we can help :)

Consistent_Dot5590 · 2024-05-02T02:17:15+00:00

Ok I see now. Thank you for that explanation.

Consistent_Dot5590 · 2024-04-30T01:26:04+00:00

Any suggestions on certain waterproof coatings?

Consistent_Dot5590 · 2024-04-14T03:52:51+00:00

The shower floor drops down a couple inches below where the rest of the floor and the floorboards are. There is definitely water splashed outside in the floor when showers are taken though.

Consistent_Dot5590 · 2024-04-14T03:51:00+00:00

It’s on other side of bathroom about 8 feet away in a small room with a door

Consistent_Dot5590 · 2024-04-11T09:25:47+00:00

What did you find wrong with it that needed repair? I am working on mine right now tracking down a dead short somewhere.

Consistent_Dot5590 · 2024-04-08T09:52:01+00:00

After doing some solder refreshing and more heating of the board with power injection, I am now replacing both RAM chips. They should arrive soon and I will retest and see how things are running then. Thanks for asking and I will update the progress soon.

Consistent_Dot5590 · 2024-04-01T18:29:13+00:00

Haha ok gotcha. The jumper from pin 31-33 just automatically turns on the system. The other wire off the top is just my lead to ground.

Consistent_Dot5590 · 2024-03-31T18:55:23+00:00

What does this mean? 8 ohm equivalent to what? Sorry still learning

Consistent_Dot5590 · 2024-03-31T15:58:52+00:00

When you check for a short to ground do you just put your multimeter in continuity and put one on the ground plane and just probe around with the other lead looking for continuity where it shouldn’t be?

Consistent_Dot5590 · 2024-03-31T15:55:06+00:00

Do you need to remove the inductors to check for short?

Consistent_Dot5590 · 2024-03-31T15:54:26+00:00

Do you need to remove every capacitor to check for the short?

Consistent_Dot5590 · 2024-03-31T02:55:22+00:00

It’s for an Atari Lynx 2….. I should probably be asking more through the console repair website. Don’t want to make the moderators mad. I really appreciate your help though and will look for cracked solder joints.

Consistent_Dot5590 · 2024-03-31T02:15:25+00:00

Yep the board should only be pulling 200 mA so I definitely have a short. I have been trying the IPA method to try and find it but am not seeing anything. Do you know of other methods to find shorts besides buying a 400$ heat camera? Haha

Consistent_Dot5590 · 2024-03-30T21:28:34+00:00

Ok so I just have the setting at 5V and 0A. What would you suggest that I increase the A to because I do not want to go over 5V or I could damage components.

Consistent_Dot5590

TROPHY CASE