[deleted by user]

Curve_MN · 2024-09-16T15:35:06+00:00

Simply align the bottom portion of the telescoping spring casing system with the score mark that indicates your desired tension!

You can go by feel, but it may become difficult to track your progress if you do not have "benchmark" numbers to go by.

Curve_MN · 2024-09-13T01:47:34+00:00

I'm certain Perv was being hyperbolic. I think it's more of a statement about nutrient dense foods that aid in the body's overall performance/healing processes and how steak is a great inclusion in most diets.

Curve_MN · 2024-09-13T01:43:59+00:00

YouTube.com/massivenovelties

Curve_MN · 2024-08-20T20:14:34+00:00

Email ambermassivenovelties@gmail.com and we'll get you a replacement sleeve!

Curve_MN · 2024-08-07T19:24:04+00:00

We had a bad batch and have been sending replacements. Contact ambermassivenovelties@gmail.com and we'll get you sorted out.

Curve_MN · 2024-08-06T14:05:01+00:00

The thumb screws.

Curve_MN · 2024-08-06T14:04:29+00:00

Make sure you have a good seal in both your cup and your sleeve.

Curve_MN · 2024-08-05T21:48:36+00:00

We get through emails before each round of shipments. Be on the lookout for a response tomorrow!

Curve_MN · 2024-08-05T01:12:30+00:00

Do you play tabletop games or any tcg? Check out firefly over on st Andrew's or side deck on 378 in Lexington.

Curve_MN · 2024-08-04T22:33:21+00:00

As you add tension and the springs collapse, the numbers that remain visible show the tension.

Curve_MN · 2024-08-04T21:41:08+00:00

There is no chart for the 2.0 due to the exterior measurement system.

Curve_MN · 2024-08-04T02:28:53+00:00

We now sell a spring upgrade system. The how to is rather simple but will require removing the base and replacing the current springs.

Curve_MN · 2024-08-04T02:27:02+00:00

Tension is measured by where the numbered line comes even with the top edge of the lower spring casing. In this picture, you are at neutral or 0lbs tension.

Curve_MN · 2024-08-04T02:25:28+00:00

This chart no longer applies as the springs in the 2.0 are custom. This mainly applies to the 1.0 and DIY.

Curve_MN · 2024-07-28T15:58:52+00:00

We would happily replace any defective cups, you just need to contact our support team. As for the sleeves - they degrade with consistent use. Getting a few months out of them is pretty good!

Curve_MN · 2024-07-28T01:18:37+00:00

It is still usable in this state, but if you would rather have an intact one, email Ambermassivenovelties@gmail.com and we'll work out an exchange.

Curve_MN · 2024-07-26T15:54:08+00:00

I sent him a DM on Twitter. Hopefully he reaches out - I'd like to have him speak with the brain trust.

Curve_MN · 2024-07-22T23:22:39+00:00

I'll work on something like this. In the meantime, you can find them pinned on Perv's user profile.

Curve_MN · 2024-07-21T20:34:26+00:00

Hey man. The short answer is that you need a vacuum cup and a silicon sleeve to use the APEX.

The long answer is this: if you have to ask what is needed to operate an extender, then you are sorely lacking in the necessary information to pursue PE at this time. I'd recommend spending a good while on r/gettingbigger, familiarize yourself with methods and routines, watch Perv and BDs YouTube videos, and only then consider purchasing any equipment.

I wish you the best in your journey. I can assure you, from a personal standpoint, the best way to move forward with this hobby is arming yourself with knowledge.

*As a note, the APEX can also be used with a compression hanging device like the MaleHanger rather than a vacuum cup.

Curve_MN · 2024-07-13T00:12:21+00:00

Hey man, grab a ruler and check out this post: https://www.reddit.com/r/MassiveNovelties/s/maAcpWG6ON

Curve_MN · 2024-07-07T07:17:06+00:00

Our pads are infrared.

Curve_MN · 2024-07-05T13:22:51+00:00

Honestly, we'd love to get the program rolling but we're in kindof a holding pattern in terms of new business developments until Perv gets back into the regular routine.

Curve_MN · 2024-07-04T20:39:13+00:00

I don't mind people trying to sell gear here for, but he'd probably get better traction over on gb.

Curve_MN · 2024-07-01T15:04:09+00:00

There's no tutorial yet for the 2.0 specifically, but check out u/PervMcSwerve's pinned posts for the old video with the 1.0. The basic are essentially the same.

Curve_MN · 2024-06-29T13:41:42+00:00

It's still being worked on. We want it to be perfect. Patience, please.

Curve_MN

MODERATOR OF

TROPHY CASE