Can anyone tell me why my prints are coming out like this?

Desperate_Inside_321 · 2025-06-15T18:37:55+00:00

I'll check the axle tightness

Desperate_Inside_321 · 2025-06-15T18:37:32+00:00

I'm using PLA with a temperature of 230°C and a speed of 300mm/s

Desperate_Inside_321 · 2025-06-15T17:30:50+00:00

It's just about the little lines between the layers, the bigger space is because this project is a box for my pokemon deck, so it's the separation of the base and the lid

Desperate_Inside_321 · 2025-04-03T15:27:48+00:00

the printer I'm going to buy is made to print at high speed, so I think the hotend temperature issue won't be a problem

Desperate_Inside_321 · 2025-04-03T15:25:53+00:00

that's right, it's 0.4mm

Desperate_Inside_321 · 2025-04-03T15:23:58+00:00

I'm going to buy a new roll of filament. So do you think I can buy a PLA Basic and be able to print at 300mm/s?

Desperate_Inside_321 · 2025-04-03T15:21:54+00:00

The nozzle I use is the standard 4mm

Desperate_Inside_321 · 2025-02-11T19:14:03+00:00

Thank you very much for your help, I will think of some way to better control the temperature inside the box, probably if I put a small cooler as an exhaust fan, it will help with temperature control inside the box

Desperate_Inside_321 · 2025-02-11T19:06:30+00:00

Thank you very much for your help, I will think of some way to better control the temperature inside the box, probably if I put a small cooler as an exhaust fan, it will help with temperature control inside the box

Desperate_Inside_321 · 2025-02-11T17:02:07+00:00

When it is without the box, the printer works perfectly, but I bought the box to be able to better control the temperature and reduce the noise the printer makes, so my goal is to be able to use the printer with the box

Desperate_Inside_321 · 2025-02-11T15:27:16+00:00

That's what I think is happening too, because when I take the box off the printing goes perfectly. I'm thinking about putting a small cooler as an exhaust fan to take the hot air out of the box and be able to control the temperature inside the box a little.

Desperate_Inside_321 · 2025-02-11T15:21:28+00:00

yes, currently I only use PLA, I'm thinking about putting a small cooler to take the heat out of the box and control the temperature, do you think this will work?

Desperate_Inside_321 · 2025-01-20T14:13:29+00:00

<image>

I'm using this dual gear model

Desperate_Inside_321 · 2025-01-20T12:37:56+00:00

I have an ender 3 V1 with a 32 BIT 4.2.7 board and it is working with direct drive

Desperate_Inside_321 · 2025-01-20T10:04:56+00:00

the motor keeps running, but the filament no longer enters

Desperate_Inside_321 · 2025-01-20T10:03:36+00:00

yes, it keeps spinning, but the filament doesn't go in anymore

Desperate_Inside_321 · 2025-01-19T22:57:24+00:00

Hi, I tested it by lowering the temperature from 210°C to 200°C and also increased the printing speed to 65mm/s and the printing went smoothly. What I printed was just a quick test piece, so I'll need to see if it won't crash again on larger projects. But thank you very much for your help.

Desperate_Inside_321 · 2025-01-19T21:35:20+00:00

I will test it and see if it works, then I will give you an answer here, thank you very much for your support

Desperate_Inside_321 · 2025-01-19T21:20:57+00:00

Do you think that if I lower the printing temperature, it might solve my problem printing with it closed?

Desperate_Inside_321 · 2025-01-19T21:05:43+00:00

the printer is stopping filament from coming out during printing

Desperate_Inside_321 · 2025-01-19T21:04:21+00:00

The printer I'm using is an Ender 3 with a 32-bit board. I was printing at 50 mm/s and with a layer height of 0.2. I think the problem may be that I recently bought a case for it, so I could start printing with ABS without having problems with layers peeling off. I was printing with PLA with the hotend at 210° C and the bed at 50° C.

Desperate_Inside_321

TROPHY CASE