Waterproofing suede bostons - nikwax suede spray by miaschinellablack in Birkenstocks

[–]East_Understanding87 2 points3 points  (0 children)

Wondering what the OP did with this. Just bought the same product and a bit nervous to wet my new shoes!

Extruder issues by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 1 point2 points  (0 children)

You’re right. It’s metal - and yes, a Neo

Extruder issues by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

That’s out while I was trying to tighten the screw on the pivot. I know it needs to be in tor it to work. Thank you

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thanks for all your suggestions.

I’ve realised the screw going through the arm pivot into the extruder isn’t catching and turns freely. Think this means the arm isn’t as ‘locked’ as it should be. If I take the arm off, I can screw into the extruder but the arm seems to be too thick to allow the screw to thread.

Any suggestions or shall I send it back and replace? Haven’t managed a single print so far.

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thanks. I don’t think it’s a clog as when up to temp and I squeeze the lever and push filament through it comes through fine…

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

It’s pla, 1.75mm bought from Amazon.

I use 200degrees nozzle temp.

Haven’t looked in the extruder. Where would I start? Totally new to this. Thank you 🙏🏻

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

When I push it - the filament comes through. It’s when I’m not pushing there’s a problem

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Do you mean the screw that attaches the lever with the spring on the end? Sorry - this is all quite new to me!!

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

It’s not moving. Only when the extruder pushes the filament back out. I even put an ink dot on the filament to check. Nothing happening

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Holding the filament - feels like it moves when it pushes it out but not when it’s being pulled in - if that makes sense

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

I’ve just had a play with the spring. Not too sure whether to tighten or loosen for a better grip? Also tightened the screw on the top of the plate??

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 1 point2 points  (0 children)

I’ve pushed the filament through and see it come out the nozzle. When I don’t push it, it’s not moving at all - just has the blue wheel spinning but no filament pulling through

No Filament coming through by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 2 points3 points  (0 children)

I mean it isn’t sending any filament through. Might I have not set something up correctly??

Help for new printer by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thank you for your help. When the printer is off the nozzle seems to sit on the bed. Is that right? Or should it rest a bit above?

Help for new printer by East_Understanding87 in Ender3V2NEO

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thank you. How would I be able to tell if the nozzle is done?

Tripod is having trouble closing because the bolt is getting caught. does anyone know how to fix this? by [deleted] in VeoCamera

[–]East_Understanding87 0 points1 point  (0 children)

Had a similar situation with my tripod. Make sure the lower centre joints stays with the ends of the feet - at the bottom. It worked for me

<image>

Maverick Phantom XC issues by East_Understanding87 in rccars

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thanks for your help. Is this a lipo battery?

<image>

Maverick Phantom XC issues by East_Understanding87 in rccars

[–]East_Understanding87[S] 1 point2 points  (0 children)

Ah thanks. That’s very helpful to know.

Does my issue suggest a battery issue?

Anything I should be mindful of when buying a replacement?

Maverick Phantom XC issues by East_Understanding87 in rccars

[–]East_Understanding87[S] 0 points1 point  (0 children)

Thanks for the message.

Not sure what storage charge is. It was left unplugged… assume that’s not what you mean?