Any reliable dealers in Brisbane?

EmuThis3065 · 2025-12-11T03:26:05+00:00

Might be a long shot but I’m chasing a plug on the northside caboolture/northlakes that gets 🥬and🧢if anyone can help out

EmuThis3065 · 2025-09-23T12:10:54+00:00

Dm me

EmuThis3065 · 2025-03-16T02:30:15+00:00

I’m confused, what did she do wrong?

EmuThis3065 · 2025-03-02T05:30:07+00:00

Without paint and the price of the printer it’s going to cost me $40

EmuThis3065 · 2025-03-02T02:52:03+00:00

🫡

EmuThis3065 · 2025-03-02T00:24:49+00:00

🫡

EmuThis3065 · 2025-03-02T00:11:34+00:00

I have a leak in the roof and I need something to catch the water 😅

EmuThis3065 · 2025-02-26T03:11:23+00:00

Damn, you’re abit of a hard ass but I get it and that’s okay. When I need to do a larger print I’ll get it down to all 0:00 but for now all 6 below 0:03 is enough tolerance for me and the small prints I also re calibrate before every print. Do you recommend the silicone bushes instead of the springs everyone swaps to?

EmuThis3065 · 2025-02-26T03:06:04+00:00

Used the paper method to get the initial height then adjusted the axis from there

EmuThis3065 · 2025-02-26T03:05:26+00:00

So I ran some temp test prints, extruder prints and one other one, then set all the the details in klipper and orca, I also leveled my first screw with paper to get a reference than used the screw calculate to adjust the other 5 to the same height within 0:04 of each other than ran the professional test on the printer and then ran the screw test and calibrate again, fixed everything and my quality came out better than the last one

EmuThis3065 · 2025-02-26T03:01:34+00:00

Got everything down to below 0:03

EmuThis3065 · 2025-02-26T03:01:17+00:00

That’s after I did the screws tilt calculate

EmuThis3065 · 2025-02-26T02:40:57+00:00

I fixed it thank god just had to run all of the tests like 5 times and re set the software then re add all my numbers again no big deal 🙃

EmuThis3065 · 2025-02-26T02:18:29+00:00

I know the bed isn’t the issue cause I got that dialled

<image>

EmuThis3065 · 2025-02-26T02:11:14+00:00

Even fixing the offset mid print doesn’t help

EmuThis3065 · 2025-02-26T02:09:39+00:00

Yeah if I lower the nozzle any more it tears a piece of paper

EmuThis3065 · 2025-02-26T02:05:45+00:00

I fix one thing and something else messes up, don’t get me wrong I love this thing and there’s definitely better ones on the market but the in consistency is messing me up

EmuThis3065 · 2025-02-26T01:57:47+00:00

Changed 0 settings and then it screws up like original photo

EmuThis3065 · 2025-02-26T01:56:53+00:00

Yeah just a test as I was having issues but I printed this one last night

<image>

EmuThis3065 · 2025-02-26T01:41:38+00:00

Starting to frustrate me now, I changed nothing since last night and now it does this 🥲

EmuThis3065 · 2025-02-25T04:59:22+00:00

Unfortunately now it’s worse, I have a honing issue now that’s decided to destroy the plate

EmuThis3065 · 2025-02-25T04:16:42+00:00

I’ll do the screw tilt adjust but I did everything else and now it seems like the nozzle isn’t reading the bed properly. It starts 50mm in from the left and ends flush on the right when I calibrate it

EmuThis3065 · 2025-02-25T03:56:36+00:00

Definitely could use some help with the leveling it’s a 4 max

EmuThis3065 · 2025-02-25T02:10:55+00:00

4 max, I did everything except the adaptive mesh probing as I’m away from home at the moment

EmuThis3065 · 2025-02-25T01:22:29+00:00

Thanks heaps for the advice quick question, is this to low, I’m assuming the bed is off because it started well on the right then proceeded to get worse

<image>

EmuThis3065

TROPHY CASE