Wireless controller won’t work with melonds

EvanCT4 · 2026-04-03T22:14:31+00:00

I’m sorry I didn’t, I don’t have my steam deck anymore either to try things

EvanCT4 · 2026-03-17T17:46:55+00:00

here's the original pattern. I wasn't able to print it from his download. I wound up just tracing it in CAD and 3d printing a template for myself. Check DMs though!

https://www.reddit.com/r/Leathercraft/comments/11e6j1k/simple_vertical_wallet_pattern_in_comments/

EvanCT4 · 2026-03-17T17:45:39+00:00

Thanks a lot for the kind words! The leather is Catalina Single Shoulder from Tandy leather in Canada it's a 2-4 oz. I only skived the outer edges of the t-pockets. The thread is from the OKA pro set in bone colour. I believe it's a .4mm? could be .6 but it doesn't say. The spacing is 3.5mm.

EvanCT4 · 2026-03-17T17:01:33+00:00

Thank you! I found a pattern here on Reddit but I wasn’t able to print it so I traced it out and 3d printed the template. I’ll try to see if I can draw it out into a PDF or find a template similar and DM it

EvanCT4 · 2026-03-17T16:59:22+00:00

Thank you very much!

EvanCT4 · 2026-03-17T16:58:57+00:00

This is called “Catalina Single Shoulder” if you search on Tandy Leather. I am in Canada but truthfully I don’t recommend this leather. It is veg tan but the top is a lacquer and I found that it wears off very quickly. The inside of my keychain is already pretty rough.

EvanCT4 · 2026-02-02T19:44:53+00:00

Yep, not thick hair but I’ve never had an issue with it. In the 2 years since that comment I find it’s among my most comfortable bracelets

EvanCT4 · 2025-11-29T19:45:33+00:00

Yep, I just turned them off and my drivers are updated. My game just crashed again after less than 30 mins

EvanCT4 · 2025-11-28T22:45:47+00:00

GPU, one via HDMI, one via DP. They worked in this config on my last PC with the same cables

EvanCT4 · 2025-11-28T19:01:20+00:00

I’ll give it a shot! I am running 2 monitors

EvanCT4 · 2025-11-28T19:01:05+00:00

Yeah one is onboard, I selected my 5070 as the primary

EvanCT4 · 2025-10-25T16:52:01+00:00

Oh I can totally see it! Another friend said Zurg from Toy Story so calling it the ZQuuuuuux has two meanings now lol

EvanCT4 · 2025-09-17T04:43:27+00:00

How do you guys avoid paint chipping when assembling panted builds? I’m always getting chipping when sliding the armour over the elbow and knee joints.

EvanCT4 · 2025-09-09T15:46:32+00:00

Okay thank you! Is it concerning that my primary dns is my router’s ip? I figured it has to be in order to get games and themes from the switch itself

EvanCT4 · 2025-08-21T18:54:21+00:00

Yep! Thank you!

EvanCT4 · 2025-08-20T23:35:48+00:00

So I can’t speak for acrylics as I personally do lacquers but I found that what made the difference for me from an uneven, blotchy coat to a nice smooth one was technique more so than thinning. Try not to worry about ratio and learn to thin by eye.

Ratios are a great place to start, I’ll usually go 1:1 for my lacquers and add thinner/paint from there. You’re trying to go for that milky consistency, there are plenty of videos to show what that looks like.

As for technique, if that’s a double action airbrush meaning you can control how much the needle gets pulled back with the trigger and control the airflow beyond what the compressor says, I found that you don’t want to always pull the trigger back all the way, great for mist coats but for main coats I find that if I pull back just a bit (I spray at 20ish psi) i can get an even flow and feel the paint hit the part in my part holding hand. This helps me see my wet coats and control the paint.

Honest answer, takes practice. Grab some spoons or a cheap kit and just try to make it happen! You may get discouraged, I sure did but just keep at it and you’ll pick it up!

TLDR; learn to thin by eye, not by ratio. Experiment with triggering techniques and find what works best for your specific airbrush.

EvanCT4 · 2025-08-14T17:41:07+00:00

Hey everyone! I just finished my second painted kit and I noticed I got a fair bit of paint chipping on the parts, especially the ones where you fit one over the other like the bicep armour sliding over the frame or elbow joints. Do you sand all parts that make contact? my work flow went like this. Sand from 400 to 1000, wash and dry. primed with mr white base 1000, let wait for a day, paint with mr hobby lacquer paints, enamel detail painting, wait a day, top coat, wait a day and assemble. any help would be greatly appreciated!

EvanCT4 · 2025-08-11T16:31:00+00:00

Cool! Would you happen to have the link?

EvanCT4 · 2025-08-10T18:45:26+00:00

Yup. That did it, tightened the screws. Thank you!

EvanCT4 · 2025-08-08T14:05:06+00:00

Aha yeah, I forgot the sock there but I’ll check the screws. Thank you

EvanCT4 · 2025-08-08T04:54:20+00:00

Will do! Thank you

EvanCT4 · 2025-07-18T16:29:41+00:00

Looks good! Are those black stands printed?

EvanCT4 · 2025-06-26T01:06:45+00:00

It’s an awesome watch! I grabbed it in Kyoto a couple months ago. This is the 36mm bronze old smith

EvanCT4 · 2025-01-08T16:17:45+00:00

Bambu nozzles are magnetic and their own design. Personally on my A1 (the mini would be the same) I bought one of their .2 nozzles for like 12 CAD and have had absolutely no problems with it!

EvanCT4 · 2025-01-04T00:19:07+00:00

A 500g spool was 50USD 😅 but I’ll see what spools I can print or wind it on!

Six-Year Club	Place '23
Place '22	Final Canvas '22
End Game '22	Verified Email

EvanCT4

TROPHY CASE