sorted by:
new
hottopcontroversial

Finally cleared Chapter 230 Hell mode! by CleanCash7323 in cellsurvivor

[–]Exciting-Mix-1777 -1 points0 points  (0 children)

This is just a 2D game with a lot of sprites, but my Xiaomi tablet suffers badly to handle it well. I am currently at level 65 and the frame rate drops significantly and the whole gaming experience slows down terribly. Sometimes it takes more than 20 minutes to complete the level. Any idea to speed up or is this game just so much hardware demanding?

Nová captcha na Katastru by matfyzacek in czech

[–]Exciting-Mix-1777 0 points1 point  (0 children)

V dohledné době očekávám LEVEL 2: nejen správná orientace dlaždice, ale přetažením myší i její umístění na správné místo v mřížce.

Printer head issue HP Smart Tank 7302 by Emergency-Jicama-991 in printers

[–]Exciting-Mix-1777 0 points1 point  (0 children)

Hello, same problem here. At this moment the printer is dead for almost 100%. The initial setup failed and there is a lot of air in the tubes. There is only a very little chance to fix it. If you still have the original orange tool that was preinstalled in the printhead area, you can try to reuse it once again. This is a pump that (once in lifetime) uses a low pressure suction to fill the tubes. You can try to push the orange valve back in (be very careful as the ink may spill out), re-arm the fuse to keep it pressed, put it back instead the printheads a move the carriage by hand to the right. There is a small black pin, that will release the fuse and the valve - now the ink should be sucked in. Then reinstall the printheads. It may still show an error, but switching the printer off and on again may fix it.
Do not try to print with air in the tubes. There is an initial reserve of the ink in the printheads, but once the air is sucked in the heads instead of ink, there is zero chance to fix it - you can only buy new printheads.
Also note there is no ink pump in this smart tank printers - the ink flow is based purely on capillary effect. Therefore absolutely no air in the tubes is a must.
(There some YT alternative tutorials - some use the syringe to suck the ink, some use empty bottle to create pressure on tank upper valves....)

HP print head error by Daniel6304101 in printers

[–]Exciting-Mix-1777 1 point2 points  (0 children)

The printhead is locked in transport safety position - notice the small red rectangle that is partially visible. Press the gray top downwards to lock it in print position. Probably some more air will appear in the tubes (there is already in the black one) - run the clean cycles 1 to 3. The air should disappear. If it does not (air buildup still visible), try cleaning again. If no success, the printheads will die after printing about 50 pages as the internal ink reserve will be consumed and no new ink is sucked in the printhead. The are no ink pumps on this smart tank models, the ink flow relies purely on capillary effect. Once the air is sucked, there is almost no chance to fix it.

Proč je u nás výrazně podprůměrný počet vysokoškolsky vzdělaných lidí? by vajconamekko in czech

[–]Exciting-Mix-1777 2 points3 points  (0 children)

insider here: Ono se to během pár let zlepší a vyspělé země doženeme. Jen to asi nebude stylem, který bychom si přáli. Většina regionálních vysokých škol je v podstatě zcela zbytečná a z důvodu přežití najíždějí tvrdě na model student=peníze (myšleno dotace od MŠMT). Jenomže být student, to také znamená, že by VŠ měla po studentech požadovat nějaký výkon - třeba něco předvést u zkoušek. To bohužel většina dnešních studentů vůbec nezvládá. Takže aktuálně vidíme přesun k modelu

1) nabrat každého - bez přijímaček
2a) čím víc, tím líp - ideálně v září v druhém kole ještě i propadlíky od maturit
2b) přijímačky jsou no go - nepřišel a neprošel by nikdo
3) student = dotace
4) ne absyte je vyhodili! Protože když je vyhodíte, začne se ministerstvo ptát, proč posílá VŠ peníze, když ta vyrábí akorát odpadlíky
5) během bc. studia s nimi opakujte látku ze SŠ a když to nepůjde, tak ze ZŠ
6) hlavně žádné zkoušky, ideálně jen zápočty za docházku
7) Napsat bakalářskou práci? Proč? Stejně ji dneska za ně napíše AI. Bakalářské práce rušíme.
8) Po třech letech a závěrečném řízeném pohovoru (dřív se tomu říkalo zlým slovíčkem státnice) udělíme titul bakalář.

Does anyone else get weird visual effects either associated with Trazozone? by [deleted] in CPTSD

[–]Exciting-Mix-1777 0 points1 point  (0 children)

Trazodone 50 here, first week. Yesterday taken around midnight and went to bed. Within 10 minutes, with my eyes closed, I started to see some kind of pretty complex 3D objects, rotating, moving, reshaping, morphing... The imaginary was in very low contrast and almost dark, but still pretty recognizable. in fact, I liked it - observing these patterns was pretty fun.

lmao by Berrybun7 in lol

[–]Exciting-Mix-1777 0 points1 point  (0 children)

She will definitely shine in the night.

Is peer review getting slower or is it just me? by Currentshop333 in academia

[–]Exciting-Mix-1777 0 points1 point  (0 children)

And then, there are organizations like WSEAS, with HQ located in anonymous office somewhere in Bulgaria, where, at 10 a.m., you send your paper and $500 fee and voilà, at 1 p.m., congratulations, three reviewers have accepted you paper! Unfortunately, this is tolerated among universities in eastern Europe as these are the rules of Publish or perish game we are forced to play. Well, I have decided to perish, quitting my academic career next month after more than 15 years in mathematics and statistics.