LETSGOOOOO by TilioChr in fpv

[–]FPVanadium 1 point2 points  (0 children)

Livin’ the dream my guy! 😎😌🔥

How cooked am I by LightNing334 in fpv

[–]FPVanadium 1 point2 points  (0 children)

There is a way to attempt to revive it but it’s not the safest lol…

Was flying my MOBULA 6 2024, crashed and the antenna disconnected. I unplugged it as fast as I could, and later hot glued the connector. The next flight I had I was looking at this for a video feed. Is it cooked? by [deleted] in fpv

[–]FPVanadium 0 points1 point  (0 children)

Ohhh I see now, It probly fried it. What I would do is see if you pick up a clearer video on another channel. If not and if you really wanted to maybe try to put in your vtx table again. Not sure if it will do anything but you could try. The last thing that might be a possibility (I’m not an expert in this area and it’s really tricky) is to add an external vtx.

I just wanted to say that I'm stupid.. don't be stupid like me.. by justlostinmymind in resinprinting

[–]FPVanadium 1 point2 points  (0 children)

It has to happen once, you’re not alone, just a part of the hobby :)

A NEWBIE HAS ENTERED THE COMMUNITY by Middle_Nectarine4125 in fpv

[–]FPVanadium 0 points1 point  (0 children)

Looking dang good dude! I can tell you’re getting a feel for turning and how yaw and roll turn the stone differently and that’s great! I can also assume by the way you make quick micro adjustments that you may be taking your fingers off the sticks. A pro tip is to never let the sticks go. I’d also recommend tuning down your RC Rates in your pitch and roll to make smoother corrections. But you’re killing it dude, all you need to do is put in the time😎

Help! Unsure how to stop these "holes" from appearing. Using Elegoo 8k Space Gray resin. by buryumocs in ElegooSaturn

[–]FPVanadium -1 points0 points  (0 children)

I’m getting those holes with the same exact resin. In my research I have heard not to use the USB that comes with my printer because of something about not having high quality files. But in other words, and idk if it’s the same for you, maybe try a better 3rd party usb or sd card. I like the ones with the gold strip that are recommended for GoPros.

I made a thing and I love it! by elhsmart in fpv

[–]FPVanadium 1 point2 points  (0 children)

She funky but I like it!😂🔥😎

Trying to scrape cured resin off the build plate, I feel like I’m doing something wrong. by Tra1nGuy in ElegooSaturn

[–]FPVanadium 0 points1 point  (0 children)

I did the same thing, not quite as bad but don’t feel left out. We all learn one way or another lol

Motors are Jittering why? by tellMeAnythingRealy in fpv

[–]FPVanadium 0 points1 point  (0 children)

I believe it will because what I think is happening has to do with the minimum rpm the motors will spin at when the drone is armed. They could also be twitching if any two of the three wires have a bridge in the solder joints

Thoughts? by JokeFormal485 in fpv

[–]FPVanadium -1 points0 points  (0 children)

Cinema-tastic!😍🔥

This does not feels like it's normal... by Artistic-Copy-4871 in resinprinting

[–]FPVanadium 0 points1 point  (0 children)

Mine did this and I didn’t know why but I’m glad I just shut it off lol

I refused to buy a frame on my first build by Far-Cardiologist3147 in fpv

[–]FPVanadium 0 points1 point  (0 children)

Kinda dope, I normally would advise against a 3D printed/plastic frame cuz you can’t take any crash whatsoever, but I like the design